Recalls filed in 1990

Car recalls in 1990

75 recall campaigns for the vehicles on this site were filed with NHTSA in 1990, covering about 4,749,696 vehicles.

December 1990

  • 90V206000Dec 18 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    Suspension jounce bumper could contact left rear wheel brake tube when suspension is AT full jounce (bounce).

  • 90V205000Dec 17 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    Routing of the front brake hose may cause excessive hose flexing resulting in premature fatigue cracking of the outer hose cover.

  • 90V204000Dec 17 Wheels hub · BAYERISCHE MOTOREN WERKE

    Screws that attach wheel covers on original equipment wheels were not fully torqued and may gradually loosen and separate from wheels under extreme driving…

November 1990

  • 90V194000Nov 19 Sensor/control module-inactive · CHRYSLER CORPORATION

    The two air bag system front impact sensors may not be secured to their mounting brackets.

  • 90V193000Nov 14 Lower arm · GENERAL MOTORS CORP.

    Nuts used to attach lower control arms, rear spring and shackle, and rear shock absorbers do not meet specifications and could "strip".

  • 90V191000Nov 9 Lugs/nuts/bolts/studs · GENERAL MOTORS CORP.

    Lug nuts that retain wheels and wheel covers may have been torqued to lower than recommended specifications.

  • 90V001000Nov 2 Switch · SAAB CARS USA, INC.

    Abrasion on the printed circuit card in the combination neutral safety/backup lamp switch operated by the automatic transmission gear selector may cause…

October 1990

  • 90V185000Oct 16 Switch · GENERAL MOTORS CORP.

    Brake stoplamps may not illuminate or, in some cases, stoplamps will not stay illuminated all the time when brakes are applied due to a faulty stoplamp switch.…

  • 90V184000Oct 16 Doors latch · SUBARU OF AMERICA, INC.

    Torque of latch screws on front doors may loosen over time due to a gap between the latch base plate and inner door panel under the screw head.

  • 90V178000Oct 3 Labels · CHRYSLER CORPORATION

    Certification label does not contain required tire and wheel information.

  • 90V177000Oct 2 Cruise control · CHRYSLER CORPORATION

    Malfunction of fuel injection system throttle postition sensor could cause intermittent high engine idle speed immediately after starting engine.

  • 90V176000Oct 1 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    Steel braided fuel hose routing may allow contact between the hose and transmission wiring harness.

September 1990

  • 90V173000Sep 25 Hoses, lines/piping, and fittings · VOLKSWAGEN OF AMERICA,INC

    Front brake hoses of insufficient length were installed in some vehicles. These short hoses could stretch and develop cracks.

  • 90V167000Sep 20 Automatic transmission · ISUZU MOTORS LIMITED

    Putting in more transmission oil than specified CAN cause oil to bleed through air groove on to the exhaust manifold if oil temperature rises.

  • 90V166000Sep 20 Hoses/lines/piping/fittings · ISUZU MOTORS LIMITED

    Improperly installed hose on the oil cooler could come in contact with the exhaust manifold and could melt.

  • 90V170000Sep 17 Anchorage · GENERAL MOTORS CORP.

    Trucks CAN contain incorrect instructions on how to properly adjust rear seat lap-shoulder belts as required by fmvss 209.

  • 90V165000Sep 6 Storage · VOLVO CARS OF NA, INC.

    Fuel damper located behind the fuel line and the fuel rail may be improperly assembled. Over time, the solder joints could allow a small amount of fuel to leak.

  • 90V164000Sep 6 Floor shift · GENERAL MOTORS CORP.

    Transaxle shift control cable may disengage from the from the floor shift control with loss of gear indicator reference and shift selector operation.

  • 90V169000Sep 4 Labels · CHRYSLER CORPORATION

    Incorrect tire pressure placard was installed on cars; does not comply with fmvss 110.

  • 90V163000Sep 4 Automatic transmission · AMERICAN HONDA MOTOR CO.

    Due to an improperly machined internal shaft in the transmission, the pawl mechanisim may not fully engage when transmission is in the park position.

  • 90V162000Sep 4 Caliper · CHRYSLER CORPORATION

    Front disc brake caliper guide pin bolts may not have been adequately torqued and could loosen.

August 1990

  • 90V159000Aug 28 Hubcap/cover · FORD MOTOR COMPANY

    Wheels may contain cracks that could propogate in raised portion of wheel center.

  • 90V146000Aug 13 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    Fuel return hoses may break AT either crimped coupling, causing a leakage of fuel.

  • 90V145000Aug 10 Differential proportional valve · CHRYSLER CORPORATION

    Incorrect screws may have been used in installing the load sensing brake proportioning valve to its bracket causing the clamping load to be less than intended.

  • 90V144000Aug 6 Recliner · FORD MOTOR COMPANY

    The second row right hand seat assembly has a tilt forward function. A latch retains the seat in the normal ride postion, and this latch may release under…

  • 90V142000Aug 6 Caliper · VOLKSWAGEN OF AMERICA,INC

    Omission of air ducts intended to guide flow of cooling air to left and right front brake calipers could allow brake fluid to exceed allowable operating…

July 1990

  • 90V134000Jul 27 Labels · LIMOUSINE WERKS, INC.

    Gross vehicle weight ratings and tire information may be incorrect on labels.

  • 90V133000Jul 27 Labels · LIMOUSINE WERKS, INC.

    Tire placard may contain incorrect gross vehicle weight ratings and tire information.

  • 90V126000Jul 10 Windshield · AMERICAN HONDA MOTOR CO.

    Poor adhesion may occur between paint layers in the windshield mounting area due to defective paint batches or overspraying.

  • 90V123000Jul 2 Tank assembly · JAGUAR ROVER TRIUMPH INC.

    Excessive fuel vapor pressure CAN occur that, after prolonged cycling, could weaken the fuel tank structure.

June 1990

  • 90V119000Jun 15 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    Improperly torqued connections of front fuel feed and return hoses to fuel pipes AT the body rail could loosen and leak fuel into the underhood area.

  • 90V114000Jun 12 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    Fuel return hoses may break AT either crimped coupling.

  • 90V112000Jun 6 Webbing · GENERAL MOTORS CORP.

    Owners manuals did not fully explain how front shoulder belt comfort feature works.

  • 90V110000Jun 4 Defroster/defogger/HVAC system · SUBARU OF AMERICA, INC.

    The defroster lever pin of the defroster shutter door may become dislocated and allow the shutter to close, preventing defroster from functioning.

  • 90V108000Jun 4 Pedals and linkages · GENERAL MOTORS CORP.

    Loose pivot bolt holding the brake pedal to its support bracket could disengage from the nut.

  • 90V107000Jun 4 Windshield · GENERAL MOTORS CORP.

    Use of improper primer on metal surfaces of windshield and side window openings could cause low adhesion to the metal surface and would not provide retention…

  • 90V106002Jun 1 Windshield · MITSUBISHI AMERICA

    Diluted primer may have been used on the windshield opening flanges prior to windshield glass installation which would not provide the retention required by…

  • 90V106001Jun 1 Windshield · CHRYSLER CORPORATION

    Diluted primer may have been used on the windshield opening flanges prior to windshield glass installation which would not provide the retention required by…

  • 90V101000Jun 1 Gear position indication (prndl) · FORD MOTOR COMPANY

    Under certain conditions, the snap ring that locates the park gear on the output shaft of the transmission may fracture.

May 1990

  • 90V098000May 21 Sun/moon roof assembly · FORD MOTOR COMPANY

    If sunroof glass is removed and reinstalled by vehicle operator, hinge assemblies CAN be accidentally improperly mated.

  • 90V096000May 18 Storage · GENERAL MOTORS CORP.

    Plastic fuel filter assemblies may develop leaks.

  • 90V081000May 15 Cooling system fan · ISUZU MOTORS LIMITED

    AT high engine speeds, the cooling fan adapter plate, which connects the cooling fan and the fan pulley, has insufficient strength, allowing cracks to develop…

  • 90V105000May 14 Buckle assembly · GENERAL MOTORS CORP.

    Plastic components of seat belt buckle assemblies do not contain an ultra violet stabilizer, and exposure to direct sunlight and elevated interior temperatures…

  • 90V068000May 1 Air conditioner · MERCEDES-BENZ USA, INC.

    Under certain operating conditions, the plastic cover of the preresistor for the auxiliary fan may melt, possibly igniting the preresistor.

  • 90V062000May 1 Sidewall · MERCEDES-BENZ USA, INC.

    Left front and left rear tires may have been damaged by a worn chain drive of the conveyor system.

April 1990

  • 90V080000Apr 25 Sensor/control module-inactive · CHRYSLER CORPORATION

    Air bag inflator modules may not contain diffuser holes between the ignitor and propellant chambers.

  • 90V078000Apr 20 Inflator module · TOYOTA MOTOR CO., LTD.

    Air bag inflator case was incorrectly machined.

  • 90V076000Apr 17 Accelerator pedal · FORD MOTOR COMPANY

    Interference occur between bolt that secures a fuel line shield to the lower portion of the dash panel and the accelerator pedal.

  • 90V072000Apr 17 Labels · NISSAN NORTH AMERICA, INC.

    Incorrect tire inflation pressures were printed on certification labels.

  • 90V074000Apr 16 Tie rod assembly · GENERAL MOTORS CORP.

    Improperly torqued tie rod clamp fasteners could allow the tie rod to loosen and eventually separate.

  • 90V073000Apr 12 Hoses, lines/piping, and fittings · ROLLS-ROYCE MOTORS, INC.

    There is insufficient clearance between the right front brake caliper hydraulic line and the engine oil cooler line. If the lines come in contact with each…

  • 90V070000Apr 10 Anti-theft device · VOLKSWAGEN OF AMERICA,INC

    Improperly manufactured steering lock bolts could break if driver applies excessive force to a locked steering wheel in an attempt to disengage the steering…

  • 90V069000Apr 10 Recliner · VOLKSWAGEN OF AMERICA,INC

    A securing clip on the outside of hinges of the left and right front seat back may not be properly seated due to interference with seat covering material.

  • 90V065000Apr 5 Rear/other · GENERAL MOTORS CORP.

    Owner's manuals were printed with rear center seat belt information omitted.

March 1990

  • 90V058000Mar 23 Steering wheel/handle bar · CHRYSLER CORPORATION

    Lower intermediate steering shaft may separate AT the rubber isolated coupling of the shaft.

  • 90V056002Mar 21 Sun/moon roof assembly · MITSUBISHI AMERICA

    Operation of sunroof in "non-standard" manner may cause male hinge disengagement from the roof hinge receiver.

  • 90V056001Mar 21 Sun/moon roof assembly · CHRYSLER CORPORATION

    Operation of sunroof in "non-standard" manner may cause male hinge disengagement from the roof hinge receiver.

  • 90V053000Mar 15 Hubcap/cover · HYUNDAI MOTOR AMERICA

    Lock washer located under the nut that secures the front hub to the drive shaft may have had improper heat treatment and could crack.

  • 90V054000Mar 14 Seat belts · GENERAL MOTORS CORP.

    Front shoulder belt guide loop attachment fastener may pull through door mounted anchor plate.

  • 90V045000Mar 8 Warning light/devices · FORD MOTOR COMPANY

    The "fasten seat belts" warning lights may not work when the ignition is switched to the "on" position during cold ambient temperatures.

  • 90V044000Mar 1 Vehicle speed control · FORD MOTOR COMPANY

    Throttle lever may contact throttle body air inlet tube, with potential for throttle remaining open following release of the accelerator pedal.

February 1990

  • 90V039000Feb 23 Fuses and circuit breakers · ROLLS-ROYCE MOTORS, INC.

    The fuse in the rear window defroster circuit may blow due to the amperage load exceeding fuse capacity.

  • 90V038000Feb 21 Hood latch · HYUNDAI MOTOR AMERICA

    Insufficient clearance could cause the safety catch on the secondary hood latch striker to bind.

  • 90V037000Feb 21 Hoses/lines/piping/fittings · HYUNDAI MOTOR AMERICA

    The spring clamp tangs on the coolant bypass hose may contact and possibly damage the engine fuel supply hose.

  • 90V036000Feb 20 Tank assembly · GENERAL MOTORS CORP.

    During a rear end collision, the rear exhaust system heat shield, which is welded to the tail pipe assembly, may puncture the fuel tank.

  • 90V035000Feb 20 Vehicle speed control · JAGUAR ROVER TRIUMPH INC.

    Electronically controlled valves in the cruise control actuator may not function properly due to dirt entering the valves.

  • 90V031000Feb 12 Sensor/control module-inactive · GENERAL MOTORS CORP.

    The forward sensor for the air bag may have been incorrectly constructed with part of the wiring harness to the sensor reversed.

  • 90V029000Feb 12 Seats · GENERAL MOTORS CORP.

    Seat pedestals for driver and passengers may have a larger than specified slot in the center channel.

  • 90V028000Feb 12 Retractor · GENERAL MOTORS CORP.

    Misaligned rear seat safety belt shoulder retractor assemblies could cause pendulum interference, causing the belt to remain in locked position or to travel…

  • 90V026000Feb 12 Cables · FORD MOTOR COMPANY

    Battery to starter cables are longer than specified; excessive cable length could contact engine damper pulley.

January 1990

  • 90V016000Jan 30 Buckle assembly · BAYERISCHE MOTOREN WERKE

    Under certain conditions, front seat center, fold-down arm rest may contact the safety belt buckle, causing damage to the release button and preventing the…

  • 90V015000Jan 29 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    On c and k models, feed and or return fuel lines CAN contact the automatic transmission shift linkage cordon shaft. In addition, on k models lines may also…

  • 90V033000Jan 26 Foundation components · MERCEDES-BENZ USA, INC.

    Bolts used for the brake strut support do not meet specifications and may break.

  • 90V008000Jan 22 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    Fuel feed and return line connectors have incorrect line end flare configurations.

  • 90V007000Jan 22 Hydraulic power assist system · VOLKSWAGEN OF AMERICA,INC

    Power steering pump bracket is subject to breakage due to excessive tension caused by a lack of clearance between the pump mounting bracket and sealing flange…