Recalls filed in 1991

Car recalls in 1991

100 recall campaigns for the vehicles on this site were filed with NHTSA in 1991, covering about 5,637,866 vehicles.

December 1991

  • 91V222000Dec 27 Switch · ROVER GROUP, LIMITED

    The electrical switch adjacent to the brake pedal which operates the brake lamps may fail to operate.

  • 91V223000Dec 24 Air bags · TOYOTA MOTOR CO., LTD.

    The driver's occupant protection system (steering wheel and air bag) exceeds the 60g thorax criterion in NHTSA crash tests.

  • 91V219000Dec 17 Vehicle speed control · BAYERISCHE MOTOREN WERKE

    The crankcase ventilation system, vented into the intake tract of the engine AT the bellows boot ahead of the throttle housing, allows warm water vapor from…

  • 91V216000Dec 13 Tank assembly · GENERAL MOTORS CORP.

    Some chassis were shipped to body builders with damaged fill or vent opening caps on the right-hand side. If a left-hand fill system was installed on the tank,…

  • 91V215000Dec 13 Air bags · VOLKSWAGEN OF AMERICA,INC

    The airbag harness wire may have been improperly routed through an opening in the dashboard crossmember and could be pinched and chafed between two panels…

  • 91V214000Dec 6 Automatic transmission · GENERAL MOTORS CORP.

    The reverse servo apply pin may bind in the case which could cause reverse band distress (loss or slipping of reverse), reverse band drag in drive range (poor…

November 1991

  • 91V206000Nov 26 Seat belts · GENERAL MOTORS CORP.

    The front shoulder belt retractors may have reduced sensitivity of the lock-up feature and would not function in a sudden deceleration or crash.

  • 91V204000Nov 19 Suspension rear · GENERAL MOTORS CORP.

    The bolts and nuts which attach the bearing-hub assembly to the rear axle flange are not sufficiently tightened on some vehicles.

  • 91V201000Nov 18 Tank assembly · VOLKSWAGEN OF AMERICA,INC

    A crack CAN develop in the fuel tank adjacent to a seam weld in the rear of the tank.

  • 91V198000Nov 14 Automatic transmission · GENERAL MOTORS CORP.

    The console mounted shift lever may disengage from the shift control cable bracket causing loss of gear indicator reference and shift selector operation.

  • 91V200000Nov 12 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    The right front brake hose may rub against the tire during a full lock left turn, which may eventually cause wear through of the brake hose on the right front…

  • 91V195000Nov 8 Interior lighting · AMERICAN HONDA MOTOR CO.

    A washer in the cargo area light may not be properly attached, and may have fallen in the cargo light during assembly. If this occurred, and the three position…

  • 91V189001Nov 4 Automatic transmission · MAZDA (NORTH AMERICA),INC

    When the automatic transmission shift lever is placed in the park position, the park pawl does not always abut or engage the park gear.

  • 91V189000Nov 4 Automatic transmission · FORD MOTOR COMPANY

    When the automatic transmission shift lever is placed in the park position, the park pawl does not always abut or engage the park gear.

  • 91V191000Nov 1 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    The anti-lock brake system high pressure hose may leak or detach AT its crimped end fitting resulting in the discharge of hydraulic fluid.

October 1991

  • 91V186000Oct 29 Hood latch · GENERAL MOTORS CORP.

    Secondary hood latch assemblies CAN corrode, causing a high latch release effort and possibly preventing the hood from latching properly when it is closed.

  • 91V185000Oct 22 Anchorage · AMERICAN HONDA MOTOR CO.

    The left and right seat safety belt assemblies are not interchangeable. Some left seat safety belt assemblies were installed on the the right side of the car.

  • 91V184000Oct 21 Column shift assembly · GENERAL MOTORS CORP.

    A misadjustment of the park lock cable in the column shift assembly makes it possible for the steering column to lock while the vehicle is in motion and the…

  • 91V182000Oct 21 Recliner · GENERAL MOTORS CORP.

    The passenger's side easy-entry seat adjuster may fail fully lock into position after the seat back has been tilted forward and the seat slid forward, then…

  • 91V170000Oct 4 Pedals and linkages · CHRYSLER CORPORATION

    The brake pedal pad attachment to the pedal arm may not have adequate strength due to mislocation of welds, and could break.

  • 91V005000Oct 2 Seat belts · GENERAL MOTORS CORP.

    Front shoulder safety belt webbing may separate AT front belt upper guide loops on either side of the front seat.

  • 91V004000Oct 2 Fan/motor · CHRYSLER CORPORATION

    Water leaking under windshield cowl in area above heater blower motor resistor block results in corrosion of the resistor terminals.

  • 91V003000Oct 2 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    There may be hydraulic fluid contamination from condensation formation that CAN plug the ABS brake booster pump filter; stress corrosion of the master cylinder…

  • 91V002000Oct 2 Automatic transmission · SAAB CARS USA, INC.

    Improper assembly could cause the ball of the gear selector arm not to be properly fixed to the socket on the end of the gear selector cable; gear selector arm…

  • 91V168000Oct 1 Labels · TOYOTA MOTOR CO., LTD.

    Due to a computer program error, certain digits of the gvwr and the gawr appeared in incorrect locations on the certification label located on the left front…

September 1991

  • 91V167000Sep 23 Mechanical · GENERAL MOTORS CORP.

    When applied, the parking brake lever assembly may release one or more teeth, reducing the cable load to the rear brakes.

  • 91V166000Sep 23 Hood latch · GENERAL MOTORS CORP.

    The secondary hood latch spring is improperly installed or missing, leading to a condition where the secondary hood latch does not engage the secondary striker.

  • 91V165000Sep 23 Hinge and attachments · GENERAL MOTORS CORP.

    Front door interlock striker may fail, causing door frame collapse and insufficient strength for the shoulder belt anchorage.

  • 91V164000Sep 20 Anchorage · SHERROD VANS, INC.

    Seat belt anchorage bar for rear sofa failed to sustain loads required by fmvss 210.

  • 91V157000Sep 18 Rack and pinion · GENERAL MOTORS CORP.

    The intermediate shaft to steering rack lower coupling pinch bolt may be missing.

  • 91V156000Sep 18 Labels · VOLKSWAGEN OF AMERICA,INC

    The vehicle capacity weight was inadvertently omitted from placard located inside the gas filler door, as required by fmvss 11o.

  • 91V158000Sep 13 Brake fluid low warning lamp · GENERAL MOTORS CORP.

    Brake indicator light may not light when ignition is in the "on" position, the parking brake is applied, and the shift selector is in the park or neutral gear…

  • 91V162000Sep 11 Vehicle speed control · VOLKSWAGEN OF AMERICA,INC

    The center of the water separator panel located in the engine compartment between engine and firewall could bend in the event someone leans on it during engine…

  • 91V155000Sep 10 Front underhood · JAGUAR ROVER TRIUMPH INC.

    The engine harness may come in contact with the air conditioning expansion valve protection plate, causing chafing of the harness.

  • 91V147000Sep 10 Hood latch · FORD MOTOR COMPANY

    The secondary hood latch may not engage when the hood is closed.

  • 91V146000Sep 4 Selector devices · FORD MOTOR COMPANY

    The dual fuel tank selector valve may malfunction and cause an overfill condition in one of the fuel tanks, resulting in an overflow of fuel past the filler…

  • 91V145000Sep 4 Support device/strut · FORD MOTOR COMPANY

    Manufacturing errors by the supplier of the liftgate latch mechanism may cause the secondary portion of the liftgate latch not to function. If the latch is not…

  • 91V143000Sep 4 Anchorage · GENERAL MOTORS CORP.

    Under certain vehicle operations and occupant usage conditions, the safety belts CAN lockup or jam in the safety belt retractor.

August 1991

  • 91V134000Aug 6 Disc rotor · FORD MOTOR COMPANY

    Front disc brake rotors of the subject vehicles may experience severe corrosion if operated in areas where calcium chloride and sodium chloride are used…

  • 91V133000Aug 5 Conventional · GENERAL MOTORS CORP.

    The automatic apply transmission mounted parking brake lever pivot bolt "finger" may be loose.

  • 91V131000Aug 5 Automatic transmission · GENERAL MOTORS CORP.

    Transaxle shift control cable may disengage from shift control cable bracket, causing loss of gear indicator reference, and shift selector operation.

July 1991

  • 91V123000Jul 16 Caliper · GENERAL MOTORS CORP.

    Brakes may have missing rear axle outer bearing retaining ring and or greater than specified bearing end play. Either condition allows the rotor and hub…

  • 91V118000Jul 12 Automatic transmission · ISUZU MOTORS LIMITED

    The transmission fluid level gauges (dip sticks) installed in these vehicles are not to designed specifications. The gauge indicates that transmission fluid…

  • 91V122000Jul 11 Anchorage · CHRYSLER CORPORATION

    Front outboard safety belt may become difficult to latch and or unlatch due to a webbing stiffener entering the buckle housing and dislodging the buckle latch…

  • 91V119000Jul 3 Anchorage · VAN CRAFT CORP

    Safety belt anchorages did not meet load requirements of fmvss 210; belt anchorage bar pulled through the floor of vehicle when subjected to loads of fmvss 210…

June 1991

  • 91V110000Jun 26 Tank assembly · TOYOTA MOTOR CO., LTD.

  • 91V108000Jun 21 Storage · GENERAL MOTORS CORP.

    Vehicles have been shipped with the fuel tank sender seal out of position.

  • 91V102000Jun 14 Anchorage · ASC COLAMCO

    The seat belts for the front and mid-ship seats did not rest on pelvis as required by fmvss 209.

  • 91V101000Jun 14 Wheel cylinders · ALLEN COACHWORKS

  • 91V100000Jun 14 Wheel cylinders · DABRYAN COACH BUILDERS

  • 91V099000Jun 14 Wheel cylinders · FEDERAL COACH, LLC

    Rear wheel brake cylinders are too small to allow for proper braking.

  • 91V098000Jun 14 Wheel cylinders · KRYSTAL KOACH COMPANY

    Rear wheel brake cylinders too small to allow for proper braking.

  • 91V096000Jun 14 Wheel cylinders · ULTRA LIMOUSINES

    Rear wheel brake cylinders are too small to allow for proper braking.

  • 91V094000Jun 14 Wheel cylinders · LIMOUSINE WERKS, INC.

    Rear wheel brake cylinders are too small to allow for proper braking.

  • 91V093000Jun 14 Wheel cylinders · ROYALE LIMOUSINE MFRS.

    Rear wheel brake cylinders are too small to allow for proper braking.

  • 91V091000Jun 11 Automatic transmission · SUBARU OF AMERICA, INC.

    Transmission shift linkage may be incorrectly adjusted and would not be engaged in a full park position when placed in park.

  • 91V092000Jun 10 Wheel cylinders · EXECUTIVE COACH BUILDERS

    Rear wheel brake cylinders too small to allow for proper braking.

  • 91V083000Jun 10 Steering wheel/handle bar · GENERAL MOTORS CORP.

    Nut attaching steering wheel may not have been properly tightened during installation.

  • 91V087000Jun 3 Hoses, lines/piping, and fittings · VOLKSWAGEN OF AMERICA,INC

    Metal fuel lines with an incorrect contour were installed in the engine compartment. The incorrect contour CAN cause the metal fuel line to rub against the…

May 1991

  • 91V082000May 30 Automatic transmission · SUBARU OF AMERICA, INC.

    Under certain load conditions, the park gear may not disengage immediately when the transmission lever is moved from park to reverse.

  • 91V078000May 14 Linkage and cable · CHRYSLER CORPORATION

    Mismatched parking brake cable lengths to the rear wheels reduces braking ability of one of the rear wheels, in violation of fmvss 105.

  • 91V079000May 13 Antilock/traction control/electronic limited slip · MAZDA (NORTH AMERICA),INC

    A return fluid line of the front brake system is misconnected to a rear brake fluid return. When the ABS system comes into use, all the fluid from the front…

  • 91V076000May 6 Windshield wiper/washer motor · FORD MOTOR COMPANY

    The nuts which hold windshield wiper motor to the wiper module may not have been sufficiently tightened and may loosen or come off. This causes changed wiper…

  • 91V075000May 6 Anchorage · VOLVO CARS OF NA, INC.

    Safety belts are designed to be routed under a diagonal cross brace during fastening. The instructional labels for the belt routing are inadequate, and CAN…

  • 91V074000May 3 Recliner · GENERAL MOTORS CORP.

    The front seat upper hinge cover screws are too long, and interfere with the seat back inertia lock. This prevents the seat back from locking properly.

  • 91V071000May 1 Vehicle speed control · FORD MOTOR COMPANY

    The throttle cable which runs from the accelerator to the governor assembly housing may have been kinked during assembly, causing excessive wear of the cable…

  • 91V069000May 1 Hoses, lines/piping, and fittings · ROVER GROUP, LIMITED

    The right rear metal brake line could come in contact with the top of the right rear shock absorber. This could lead to an eventual fluid leak in one of the…

April 1991

  • 91V068000Apr 22 Fuel pump · VOLKSWAGEN OF AMERICA,INC

    The fuel filter housing, which serves as the base for the fuel pump (located in the fuel tank) could deform, resulting in the fuel pump becoming loose.

  • 91V067000Apr 22 Anchorage · GENERAL MOTORS CORP.

    The metal latchplates may not engage the buckle assemblies, causing a "no latch" condition. Movement of the seat occupant in this condition could cause…

  • 91V065000Apr 17 Automatic transmission · AMERICAN HONDA MOTOR CO.

    Transmission shift cable bracket CAN be damaged by the engine rocking forward on engine mounts in a minor collision.

  • 91V064000Apr 15 Linkages · VOLKSWAGEN OF AMERICA,INC

    The lock nut of the cruise control rod for the operating servo may not have been properly torqued during manufacture.

  • 91V063000Apr 15 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    Improper insertion/crimping of the hose-to-end fittings of the high pressure hose on the anti-lock brake system CAN cause detachment of the hose from the ABS…

  • 91V054000Apr 10 Knee bolster · BAYERISCHE MOTOREN WERKE

    During testing, incorrectly installed driver-side knee bolster prevented steering column from moving forward as designed to absorb impact energy from driver…

  • 91V053000Apr 10 Buckle assembly · CHRYSLER CORPORATION

    Inboard front seat belt buckle assembly straps CAN suffer fatigue failure of the strap near its anchor position.

  • 91V050000Apr 2 Accessory scissor/screw/bottle jack/lift · VOLKSWAGEN OF AMERICA,INC

    Instruction label in the trunk of vehicle is incorrect for the jack supplied with the vehicle.

March 1991

  • 91V048000Mar 18 Automatic transmission · FORD MOTOR COMPANY

    The park rod assembly contains a park cam with inadequate surface hardness, which could lead to park disengagement or no park engagement when the lever is…

  • 91V046000Mar 15 Anchorage · GENERAL MOTORS CORP.

    A right hand seat/shoulder belt retractor may have been installed in the second row left hand seat position (directly behind driver).

  • 91V042000Mar 11 12v/24v/48v battery · CHRYSLER CORPORATION

    Routing of battery main feed wiring may allow it to contact the air cleaner bracket and contnued contact may lead to an electrical short circuit.

  • 91V041000Mar 11 Flasher unit · CHRYSLER CORPORATION

    Incorrect turn signal flasher inhibits indication of signal lamp outage.

  • 91V040000Mar 11 Seats · GENERAL MOTORS CORP.

    Seat back of the rear bench seat may break away from the seat cushion in an accident.

  • 91V034000Mar 1 High/low beam dimmer switch · GENERAL MOTORS CORP.

    Cars were built missing a wire between the digital cluster and the dimmer control, thereby failing to provide AT least two levels of lighting.

February 1991

  • 91V031000Feb 19 Windshield · GENERAL MOTORS CORP.

    Poor bond adhesion between the windshield glass and the mounting, which could allow the windshield to separate from the vehicle during a collision. This fails…

  • 91V029000Feb 15 Vehicle speed control · BAYERISCHE MOTOREN WERKE

    Insufficient axial clearance exists for throttle valve, shaft, and housing due to the different thermal expansion rates of the separate parts when vehicle…

  • 91V015000Feb 15 Axle shaft · ISUZU MOTORS LIMITED

    Bearings used in the rear axle hubs on these vehicles are improperly machined; bearing could seize AT low mileages before sufficient run in is achieved.

  • 91V028000Feb 13 Bumpers · MAZDA (NORTH AMERICA),INC

    Rear bumper may be susceptible to fatigue cracking under extended trailer tow service when using a bumper mounted trailer hitch.

  • 91V027000Feb 13 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    Rear brake tube routing is contacted by fuel tank heat shield when suspension is in full jounce position. This damages the brake fluid tube, causing a leak.

  • 91V026000Feb 12 Bumpers · FORD MOTOR COMPANY

    Rear bumper reinforcement may be subject to fatigue cracking under extended trailer tow service when using a bumper-mounted trailer hitch ball.

  • 91V025000Feb 11 Tank assembly · FORD MOTOR COMPANY

    The hot plate weld which attaches the vapor vent valve carrier to the top of the plastic fuel tank may partially fracture, allowing vapor of fuel to escape…

  • 91V024000Feb 11 Tank assembly · FORD MOTOR COMPANY

    The front heat shield may contact the front of the plastic fuel tank, causing cuts or other damage to the extent of penetration.

  • 91V023000Feb 11 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    Improperly installed brake fluid tube may allow the tube to contact the steering intermediate shaft damaging the tube.

  • 91V022000Feb 8 Seat belts · NISSAN NORTH AMERICA, INC.

    Improper belt guide performance CAN cause fraying of the shoulder safety belts near the retractor.

January 1991

  • 91V012000Jan 15 Hood latch · PORSCHE CARS N.A. INC.

    Luggage in the luggage compartment and or plastic trim surrounding the safety latch may prevent the latch on the front hood from properly locking.

  • 91V019000Jan 14 Switch · ALFA ROMEO, INCORPORATED

    Headlight switch could malfunction causing sudden high beams failure.

  • 91V011000Jan 11 Foundation components drum · MOLONEY COACH BUILDERS

    Limousine failed to meet stopping distance requirements of fmvss 105.

  • 91V010000Jan 8 Fuel pump · VOLVO OF AMERICA CORP.

    If conditions of high ambient temperature, overfilling of the fuel tank, and insufficient torque on the sending unit lock ring exist simultaneously, fuel…

  • 91V009000Jan 8 Cooling unit and lines · FORD MOTOR COMPANY

    The rubber tube that connects the transmission to the transmission oil cooler (in the radiator) may disconnect causing discharge of fluid.

  • 91V008000Jan 8 Delivery · FORD MOTOR COMPANY

    Distorted fuel lines in engine compartment may contact the steering column universal joint and cause damage to the fuel line.

  • 91V020000Jan 5 Tank assembly · MAZDA (NORTH AMERICA),INC

    Front heat shield extension may contact the upper front corner of plastic fuel tank damaging or puncturing the fuel tank.

  • 91V018000Jan 4 Steering wheel/handle bar · GENERAL MOTORS CORP.

  • 91V016000Jan 1 Anchorage · FORD MOTOR COMPANY

    Brackets mounting automatic shoulder belt retractor assembly may have an understrength spot weld.