Recalls filed in 1992

Car recalls in 1992

79 recall campaigns for the vehicles on this site were filed with NHTSA in 1992, covering about 6,216,891 vehicles.

December 1992

  • 92V187000Dec 28 Vehicle speed control · GENERAL MOTORS CORP.

    A manufacturing condition in the throttle body injector (tbi) unit might occur to allow the throttle cam lever to disengage from the throttle drive shaft.

  • 92V185000Dec 24 Switch · GENERAL MOTORS CORP.

    The service brake stop lamp switch becomes inoperative.

  • 92V182000Dec 15 Fuses and circuit breakers · GENERAL MOTORS CORP.

    The fog lamps, low beam headlamps, and high beam headlamps CAN be operated simultaneously. This CAN cause the headlamp circuit breaker to overload and trip,…

  • 92V181000Dec 14 Pedals and linkages · CHRYSLER CORPORATION

    The retainer clip which secures the master cylinder input rod to the brake pedal was not installed properly, and could work loose.

  • 92V172002Dec 2 Hoses, lines/piping, and fittings · NISSAN NORTH AMERICA, INC.

    Fuel filler hoses may have been cut prior to installation by a utility knife used to open the shipping box.

  • 92V172001Dec 2 Hoses, lines/piping, and fittings · FORD MOTOR COMPANY

    Fuel filler hoses may have been cut prior to installation by a utility knife used to open the shipping box.

November 1992

  • 92V166000Nov 18 Retractor · FORD MOTOR COMPANY

    The link lever trunion on the safety belt retractor may have been damaged during installation.

  • 92V164000Nov 10 Wheels · FORD MOTOR COMPANY

  • 92V160000Nov 8 Hose, piping, and connections · GENERAL MOTORS CORP.

    The power steering gear inlet hose on these vehicles CAN fracture, causing power steering fluid to spray from hose into the engine compartment.

  • 92V161000Nov 3 Fuel system, gasoline · GENERAL MOTORS CORP.

    There is fuel leakage AT the fuel tank fill and/or vent pipe extension solder joints.

  • 92V159000Nov 3 Unknown or other · MAZDA (NORTH AMERICA),INC

    A hardtop hoist accessory kit was sold to customers who have the miata with a hardtop. The plastic buckles used to adjust strap tension CAN break after the…

October 1992

  • 92V154000Oct 23 Automatic transmission · GENERAL MOTORS CORP.

    The automatic transmission shift control cable CAN separate.

  • 92V148000Oct 14 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    On 1987 through early 1990 models, both front brake hoses CAN wear due to direct contact with the wheel opening splash shields. On the late 1990 through 1992…

  • 92V147000Oct 14 Fuel system, gasoline · CHRYSLER CORPORATION

    Fuel tank flanges were not bent as required to allow the specified clearance for the fuel tank mounting straps and fuel lines AT the tank.

  • 92V142000Oct 5 Vehicle speed control · PORSCHE CARS N.A. INC.

    The ball sockets on the cruise control linkage CAN break, allowing the cruise control linkage to become detached on one end and jam on nearby components, which…

September 1992

  • 92V139000Sep 30 Wheels · MAZDA (NORTH AMERICA),INC

    The steel spoked wheel assemblies installed as standard equipment or offered as an option on these vehicles were improperly welded during assembly of the wheel…

  • 92V140000Sep 29 Switch/wiring · BAYERISCHE MOTOREN WERKE

    The screw that secures the wiper switch AT one location and which also provides a ground for the wiper circuit, loosens as the switch is operated over a long…

  • 92V135000Sep 22 Doors latch · TOYOTA MOTOR CO., LTD.

    The electronic control unit (ECU) for the power door lock system CAN fail, causing the contacts to "weld", and resulting in door lock solenoid damage, with…

  • 92V133002Sep 21 Seat belts · FORD MOTOR COMPANY

    One or both of the bolts securing the automatic seat belt restraint system tracks to the b-pillars were not adequately tightened.

  • 92V133001Sep 21 Seat belts · NISSAN NORTH AMERICA, INC.

    One or both of the bolts securing the automatic seat belt restraint system tracks to the b-pillars were not adequately tightened.

  • 92V132002Sep 21 Master cylinder · FORD MOTOR COMPANY

    The service brake master cylinder was not properly assembled or could have been damaged by the evacuation and filling of the brake system AT the assembly plant.

  • 92V132001Sep 21 Master cylinder · NISSAN NORTH AMERICA, INC.

    The service brake master cylinder was not properly assembled or could have been damaged by the evacuation and filling of the brake system AT the assembly plant.

  • 92V131000Sep 15 Vehicle speed control · VOLKSWAGEN OF AMERICA,INC

    The venturi tube located in the throttle valve housing CAN become loose and fall against the throttle plate.

  • 92V128000Sep 15 Suspension front · CHRYSLER CORPORATION

    The front suspension lower control arm tension strut washers CAN crack and fall off due to hydrogen embrittlement.

  • 92V129000Sep 8 Wheels · GENERAL MOTORS CORP.

    The 19.5 x 6 front steel wheel disc cracks outside the mounting bolt circle and ends AT the hub's diameter.

  • 92V127000Sep 3 Power assist · GENERAL MOTORS CORP.

    The brake pedal assembly has a pushrod pin that is too small and it is installed in the wrong position, causing an increased brake pedal ratio and a decreased…

  • 92V124000Sep 1 Recliner · GENERAL MOTORS CORP.

    The power seat or recliner wiring harness CAN be pinched or CAN chafe on the seat frame or spring support rod, wearing through the wire insulation and causing…

August 1992

  • 92V123000Aug 24 Labels · FORD MOTOR COMPANY

    The tire certification labels incorrectly identify the vehicle tire requirements as p235/75r15 sl (standard load), rather than as p235/75r15 xl (extra load).

  • 92V117000Aug 19 Fuel system, gasoline · FORD MOTOR COMPANY

    Fatigue cracks CAN develop in the solder joint between the fuel return tube and the fuel pump sending unit located AT the top of the fuel tank.

  • 92V113000Aug 17 Buckle assembly · FORD MOTOR COMPANY

    The rigid mounted safety belt buckles are defective in three ways. First, a fastened safety belt buckle will not unlatch when the release button is depressed.…

  • 92V112000Aug 4 Gasoline · FORD MOTOR COMPANY

    The sound insulation on the engine side of the dash panel CAN contact the exhaust manifold.

July 1992

  • 92V109000Jul 24 Frontal · AMERICAN HONDA MOTOR CO.

    The passenger side airbag assembly was produced without igniter material.

  • 92V106000Jul 17 Filler pipe and cap · GENERAL MOTORS CORP.

    The vehicles were assembled with an incorrect suspension upper spring seat AT the right-rear position. If the vehicle is involved in a rear impact accident,…

  • 92V111000Jul 13 Headlights · TOYOTA MOTOR CO., LTD.

    There CAN be interference with the headlamp housing if headlamp bulbs are replaced with any brand other than koito brand bulbs.

  • 92V103000Jul 13 Switch · FORD MOTOR COMPANY

    The stop lamp switches could intermittently malfunction resulting in the stop lamps not illuminating when the brakes are applied.

  • 92V101000Jul 10 Vehicle speed control · BAYERISCHE MOTOREN WERKE

    Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

  • 92V098000Jul 8 Power train · GENERAL MOTORS CORP.

    The transaxle valve assemblies were improperly machined. Vehicles may not properly engage in neutral or park, even though the gear selector indicates the…

  • 92V091001Jul 6 Air bags · GENERAL MOTORS CORP.

    The steering wheel center hub CAN fracture during certain frontal and near frontal vehicle collisions.

  • 92V091000Jul 6 Air bags · ISUZU MOTORS LIMITED

    The steering wheel center hub CAN fracture during certain frontal and near frontal vehicle collisions.

  • 92V094000Jul 1 Seat belts · GENERAL MOTORS CORP.

    The shoulder belt guide loop plastic covering may crack and expose the steel sub-plate.

June 1992

  • 92V089000Jun 24 Wheels · GENERAL MOTORS CORP.

    The steel wheels exhibit fatigue cracking around the circumference of the wheel lug nut mounting surface due to wheel bending caused by frequent misuse of tire…

  • 92V083000Jun 11 Hoses, lines/piping, and fittings · MERCEDES-BENZ USA, INC.

    The plastic brake hydraulic hose from the automatic slip control unit was misrouted too close to the pre-resistor for the electric auxiliary engine cooling fan…

  • 92V080000Jun 2 Air bags · FORD MOTOR COMPANY

    The air bag modules do not meet the ford specifications for high ambient temperature performance.

May 1992

  • 92V075000May 19 Hoses, lines/piping, and fittings · FORD MOTOR COMPANY

    The rear brake lines have inadequate clearance between the brake tube and the vehicle underbody in the area of the left rear wheel opening.

  • 92V077000May 18 Glass, side/rear · GENERAL MOTORS CORP.

    Vehicles were incorrectly equipped with standard rear windows instead of the necessary riveted installation seal assemblies.

  • 92V073000May 18 Gear box (other than rack and pinion) · FERRARI NORTH AMERICA

    The steering box extension fasteners were manufactured with inferior material.

  • 92V072000May 18 Steering wheel/handle bar · FERRARI NORTH AMERICA

    The upper steering column locknut was manufactured with inferior materials and inferior self-locking properties.

  • 92V071000May 18 Fuel injection system · FERRARI NORTH AMERICA

    The aluminum fuel line fittings on certain fuel injection lines corrode, causing the fuel line fittings to break.

  • 92V070000May 13 Hood latch · CHRYSLER CORPORATION

    The hood latch assembly may not have been properly installed and the secondary hood latch may be prevented from engaging when the hood is closed.

  • 92V066000May 11 Wiring · GENERAL MOTORS CORP.

    The optional remote entry module may have a fault which causes random actuation of interior lamps, door locks, and/or tailgate release. This actuation may…

  • 92V065000May 11 Wheels · FORD MOTOR COMPANY

    Children CAN accidentally lock themselves in the footwell area of the rear-facing third seat, or in the storage compartment in station wagons not equipped with…

  • 91V172000May 4 Anchorage · GLAVAL BUS DIVISION

    The safety belt anchorage for the rear bench seat failed to comply with the standards of fmvss 210.

  • 92V064000May 1 Control arm · VOLKSWAGEN OF AMERICA,INC

    The track control arms used to support the front wheels were improperly welded in the area of the flexible bushing mounting hole. This causes a gradual opening…

April 1992

  • 92V061000Apr 27 Vehicle speed control · PORSCHE CARS N.A. INC.

    The rear engine compartment cover near the cruise control servo motor slips, causing the safety clip in the servo motor arm to bind due to insufficient…

  • 92V058000Apr 14 Hoses, lines/piping, and fittings · VOLKSWAGEN OF AMERICA,INC

    The fuel hose attached to the fuel distribution rail on the engine may shrink beyond the clamp force of the fuel hose clamps, allowing fuel to leak.

  • 92V056000Apr 14 Pedals and linkages · GENERAL MOTORS CORP.

    The pivot bolt holding the brake pedal to its support bracket may be improperly tightened and may not have engaged the locking material on the bolt. The bolt…

  • 92V055000Apr 14 Seats · BAYERISCHE MOTOREN WERKE

    The vehicle failed to comply with fmvss 208. The driver's chest resultant acceleration exceeded the allowable 60 g's in a crash test when the seat height…

  • 92V050000Apr 14 Heater core · VOLKSWAGEN OF AMERICA,INC

    The end cap connecting the heat exchanger's core to the engine cooling system could rupture and allow hot coolant to escape into the passenger compartment.

  • 92V048000Apr 3 Vehicle speed control · GENERAL MOTORS CORP.

    The accelerator cable may have been kinked during vehicle assembly. The kink in the cable CAN cause either a high effort accelerator cable, sticking…

  • 92V047000Apr 2 Anchorage · ACTION VANS, INC.

    Installation of safety belt anchorage bolts failed to comply with fmvss 210.

  • 92V045000Apr 2 Control arm · MAZDA (NORTH AMERICA),INC

    The lower arm ball joints on both sides of the front suspension may not have been torqued to specification.

  • 92V046000Apr 1 Foundation components · TOYOTA MOTOR CO., LTD.

    The anti-lock brake/traction control computer logic program was incomplete, resulting in the trapping of brake fluid pressure in the rear brake lines. Failure…

  • 92V044000Apr 1 Tank assembly · SUBARU OF AMERICA, INC.

    A misalignment of the rear seat cushion latching bracket reinforcement plate to the floor required a machine tap to clear the opening for a mounting bolt. The…

  • 92V043000Apr 1 Power window devices and controls · GENERAL MOTORS CORP.

    Moisture CAN enter the express-down electronic control module and cause a short circuit that causes window operation without operator control, and leaves the…

  • 92V038000Apr 1 Hand control/valve · VOLVO GM HEAVY TRUCK CORP

    The trailer hand brake control system may have the wrong valve installed which limits the air pressure to the trailer brakes below the required pressure.

March 1992

  • 92V039000Mar 24 Tie rod assembly · GENERAL MOTORS CORP.

    There may be fatigue fractures of the tie rod through the damper stud mounting hole.

  • 92V035000Mar 17 Linkage and cable · CHRYSLER CORPORATION

    The parking brake cable springs are too long, which CAN cause full compression of the return spring before full engagement of the brake pads to the drum when…

  • 92V030000Mar 10 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    The anti-lock brake system high pressure pump may be porous which will result in brake fluid leakage.

  • 92V026000Mar 3 Shoes/linings · FORD MOTOR COMPANY

    A revised brake lining noise insulator resulted in a decrease in the thermal insulation between the brake lining and the front brake caliper piston. This…

February 1992

  • 92V027000Feb 27 Shoes/linings · MAZDA (NORTH AMERICA),INC

    The rear brake linings CAN change over time. As the brakes wear, the coefficient of friction CAN increase, producing inconsistent rear brake performance and…

  • 92V023000Feb 19 Unknown or other · FORD MOTOR COMPANY

    Incorrect instrument panel wiring assemblies in some vehicles will not actuate the "anti-lock" brake warning lights.

  • 92V015000Feb 14 Steering wheel/handle bar · CHRYSLER CORPORATION

    The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.

  • 92V016000Feb 11 Body door · CHRYSLER CORPORATION

    The owner's manual incorrectly states that the front passenger door cannot be opened from the inside if the door is locked until the lock control handle has…

  • 92V014000Feb 7 Rack and pinion rack · PORSCHE CARS N.A. INC.

    One or more of the bolts mounting the steering rack to the chassis of the vehicle may have been stretched, due to over torquing in the manufacturing process,…

January 1992

  • 92V012000Jan 28 Structure body · GENERAL MOTORS CORP.

    The glove compartment door will not remain closed during certain load forces associated with a vehicle crash. This does not comply with the requirements of…

  • 92V009000Jan 23 Ignition · JAGUAR CARS

    The high tension lead from the ignition coil CAN move from the production location closer to the #4a fuel injector hose. This could lead to the outer and inner…

  • 92V006000Jan 14 Body door · FORD MOTOR COMPANY

    Water CAN enter the door latch release cable. If the vehicle is operated in below freezing temperatures, the water in the door latch release cable CAN freeze…

  • 92V005000Jan 14 Labels · CHRYSLER CORPORATION

    The tire selection and rims ceritification label may have incorrect information.

  • 92V003000Jan 10 Seat belts · GENERAL MOTORS CORP.

    The front door shoulder belt guide loops may be cracked and are not in compliance with fmvss 208.