Recalls filed in 1993

Car recalls in 1993

83 recall campaigns for the vehicles on this site were filed with NHTSA in 1993, covering about 7,485,373 vehicles.

December 1993

  • 93V216000Dec 14 Seats · GENERAL MOTORS CORP.

    The seats have been assembled without bolts that connect the upper slave hinge to the seat back frame, or without bolts that connect the seat to the seat…

  • 93V215000Dec 14 Lugs/nuts/bolts/studs · CHRYSLER CORPORATION

    Wheels with misformed lug nut seats were installed on these vehicles. This causes reduced nut to wheel contact area and limits the wheel self-centering…

  • 93V213000Dec 14 Recliner · CHRYSLER CORPORATION

    The seat back latch lever pivot rivets are susceptible to distortion. The distorted assemblies allow the seat back release latch lever to remain in the…

  • 93V212000Dec 13 Rear/other · GENERAL MOTORS CORP.

    The safety belt retractors for the rear center position are missing a pawl spring and in case of an accident, will allow the safety belt webbing to extend…

  • 93V210000Dec 13 Steering wheel/handle bar · CHRYSLER CORPORATION

    The molded plastic pin which connects the upper steering column shaft and the lower column shaft may have been sheared prior to installation of the steering…

  • 93V208000Dec 9 Frontal · AMERICAN HONDA MOTOR CO.

    The passenger-side air bag modules contain incorrect inflators which are out of specification for the passenger side air bag.

  • 93V205000Dec 7 Hoses, lines/piping, and fittings · PORSCHE CARS N.A. INC.

    The hydraulic brake pressure reduction valve causes the rate of hydraulic pressure reduction to slow down, which may result in the rear wheels locking-up even…

  • 93V204000Dec 7 Fuses and circuit breakers · PORSCHE CARS N.A. INC.

    After the engine has been turned off, the rear heater will automatically operate in order to dissipate heat in the engine heating system. During this…

  • 93V199000Dec 1 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    The fuel lines on these vehicles may have been misrouted and may contact the "air" check valve. The high temperatures from the "air" check valve could allow it…

November 1993

  • 93V189000Nov 30 Hood latch · AMERICAN SUZUKI MOTOR CORP.

    Mislocated attaching spot welds of the hood striker assembly cause cracks to start on the hood inner panel. If cracks occur, the hood striker assembly may not…

  • 93V196000Nov 29 Seat belts · HYUNDAI MOTOR AMERICA

    The motorized shoulder belt CAN travel slowly or chatter in the track and may eventually stop tracking and become inoperative.

  • 93V194000Nov 23 Conventional · FORD MOTOR COMPANY

    These vehicles do not comply with fmvss 105, "hydraulic brake systems." the parking brake application force for a foot operated control system should not…

  • 93V193000Nov 23 Power adjust · FORD MOTOR COMPANY

    An unused power seat harness connector is positioned on the rubber floor mat under the seat. If the vehicle is operated in cold weather in areas that have…

  • 93V192000Nov 23 Fuel system, gasoline · HYUNDAI MOTOR AMERICA

    The vehicles failed the lateral moving barrier impact test requirements of fmvss 301, "fuel system integrity." the fuel leakage from the gas tank exceeded the…

  • 93V189001Nov 23 Hood latch · GENERAL MOTORS CORP.

    Mislocated attaching spot welds of the hood striker assembly cause cracks to start on the hood inner panel. If cracks occur, the hood striker assembly may not…

  • 93V190000Nov 22 Vehicle speed control · GENERAL MOTORS CORP.

    Vehicle description: passenger vehicles. During very cold weather, water thatn enters the accelerator control cable conduit freezes and causes the accelerator…

  • 93V187000Nov 16 Seats · GENERAL MOTORS CORP.

    The recliner mechanism and the seat frame may have foam and/or vinyl between them, creating a "soft" joint. This "soft" joint results in lower than specified…

  • 93V184000Nov 10 Air bags · FORD MOTOR COMPANY

    These vehicles were built with nonfunctional air bag diagnostic modules intended for certain vehicles over 8,500 bls. Gvwr.

  • 93V180000Nov 5 Cooling unit and lines · FORD MOTOR COMPANY

    The transmission fluid rubber tube connecting the transmission to the transmission oil cooler located in the radiator CAN become disconnected from the…

  • 93V179000Nov 1 Seat belts · JAGUAR MOTORS, INC.

    The normal lockup function of the automatic (passive) belt reel CAN cause the belt motor winch assembly to lockup such that the passive belt system will not…

October 1993

  • 93V175000Oct 29 Air conditioner · VOLKSWAGEN OF AMERICA,INC

    The plastic material of the center air flow duct, which is fastened by two mounting screws to the ceiling of the passenger compartment, CAN crack and…

  • 93V174000Oct 29 Body door · MAZDA (NORTH AMERICA),INC

    Resin molded front handles fail AT the door latch actuating rod attachment, freeing the rod to fall inside the door frame. Subsequent lowering of the…

  • 93V173000Oct 22 Suspension front · CHRYSLER CORPORATION

    Front suspension track bar attachment to the axle may not be adequately tightened.

  • 93V169000Oct 15 Frontal · FORD MOTOR COMPANY

    If the passenger-side air bag deploys in an accident and there is no passenger in that seating position, the air bag CAN detach from, and deform, the mounting…

  • 93V164000Oct 1 Vehicle speed control · GENERAL MOTORS CORP.

    The throttle cable CAN become disengaged from the retaining bracket.

September 1993

  • 93V163000Sep 27 Mid/rear assembly · GENERAL MOTORS CORP.

    The rear bench seat does not meet the load requirements of fmvss 207, "seating systems," because the manual latch mechanism on the folding full bench rear seat…

  • 93V162000Sep 27 Vehicle speed control · GENERAL MOTORS CORP.

    The cruise control cable may separate from the conduit end fitting while engaged and accelerator control could be lost.

  • 93V161000Sep 27 Anchorage · CHRYSLER CORPORATION

    The two rear inboard safety belt attachment bolts may have inadequate thread engagement into the floor pan anchor nuts.

  • 93V160000Sep 27 Springs · FORD MOTOR COMPANY

    As a result of inherent vibration in these engines, the throttle return springs CAN fracture.

  • 93V159000Sep 27 Fuel injection system · FORD MOTOR COMPANY

    The fuel rail that provides the fuel supply to the fuel injectors has an improperly formed tube which has the potential to fracture, causing fuel to leak.

  • 93V157000Sep 24 Suspension front · GENERAL MOTORS CORP.

    The suspension support assemblies do not meet general motors corporation's specification for weld integrity and the affected weld CAN fail causing the front of…

  • 93V155000Sep 24 Air bags · FORD MOTOR COMPANY

    The design of the air bag diagnostic monitor causes the driver's side air bag to deploy when the passenger door is slammed while the ignition key is turned to…

  • 93V154000Sep 21 Buckle assembly · GENERAL MOTORS CORP.

    The safety belt buckle assemblies may not latch or may not release due to the fracture of the red release push button.

  • 93V152000Sep 15 Pedals and linkages · GENERAL MOTORS CORP.

    The brake pedal push rod retainer is missing, mispositioned or not properly seated.

  • 93V153000Sep 14 Switch · GENERAL MOTORS CORP.

    The neutral start safety switch could have been fractured during installation.

  • 93V147000Sep 13 Radio/tape deck/cd etc. · TOYOTA MOTOR CO., LTD.

    Failure of a specific electronic component in the radios causes an electrical short circuit.

  • 93V145000Sep 3 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    The fuel feed hose CAN pull out of the crimped coupling AT the engine end of the hose assembly, causing fuel leakage.

  • 93V138000Sep 3 Mechanical · VOLKSWAGEN OF AMERICA,INC

    The handle of the emergency brake contains a torsion spring which is designed to ensure that the locking mechanism remains firmly engaged upon application of…

August 1993

  • 93V132000Aug 10 Alternator/generator/regulator · GENERAL MOTORS CORP.

    The generator electrical wiring is not protected against excessive current flow which may be caused by an electrical short circuit in the generator.

  • 93V131000Aug 6 Roof and pillars · PORSCHE CARS N.A. INC.

    The latch hook on the convertible top CAN crack, developing into a break of the latch hook, impairing its function.

  • 93V129000Aug 2 Hoses, lines/piping, and fittings · VOLKSWAGEN OF AMERICA,INC

    An engine preheating tube may not be properly supported due to a missing support bracket, causing the preheating tube to chafe against the right front metal…

  • 93V125000Aug 2 Tank assembly · FORD MOTOR COMPANY

    A malfunctioning check valve within the fuel pump assembly causes a portion of the unused fuel from one tank to be returned to the second tank. When this…

  • 93V119000Aug 2 Disc rotor · GENERAL MOTORS CORP.

    Severe corrosion due to road salt AT the joint of the stamped steel center section and the cast outer section CAN cause the sections to separate.

July 1993

  • 93V121000Jul 21 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    The brake hoses were manufactured incorrectly, and do not comply with fmvss 106, "brake hoses."

  • 93V118000Jul 14 Suspension front · VOLKSWAGEN OF AMERICA,INC

    Lock nuts used to hold the left and right front axles to the suspension struts may not have been properly manufactured. The lock nuts may break and cause…

  • 93V114000Jul 12 Frame and members · CHRYSLER CORPORATION

    The welding attachments of the front frame rails to the floor pan sheet metal may not be properly welded.

  • 93V113000Jul 7 Windshield wiper/washer · TOYOTA MOTOR CO., LTD.

    Certain windshield wiper components are subject to premature failure due to insufficient strength to function under high load levels.

June 1993

  • 93V108000Jun 23 Frontal · MERCEDES-BENZ USA, INC.

    Driver's side airbags do not meet certain requirements of fmvss 208.

  • 93V105000Jun 21 Anchorage · GENERAL MOTORS CORP.

    The outboard rear safety belt assembly will not release the webbing from the retracted position. This does not meet the requirements of fmvss 209, "seat belt…

  • 93V102000Jun 14 Front underhood · VOLKSWAGEN OF AMERICA,INC

    An engine compartment electrical wiring harness may have been routed too close to a sheet metal edge. The wiring CAN become damaged during normal vehicle…

  • 93V100000Jun 8 Fuel system, gasoline · FORD MOTOR COMPANY

    The fuel filler hose or fuel filler vent hose was damaged by a drill bit used to install the dso package attaching hardware onto the floor pan.

  • 93V098000Jun 4 Lugs/nuts/bolts/studs · CHRYSLER CORPORATION

    The 15 inch wheels have malformed lug nut seat configuration which causes poor nut-to-wheel contact and centering of the wheel during installation.

May 1993

  • 93V095000May 27 Vehicle speed control · MERCEDES-BENZ USA, INC.

    Due to heat effects, the throttle bushing located on the accelerator control cable, CAN fatigue and break, causing the throttle linkage to separate.

  • 93V094000May 25 Cables · GENERAL MOTORS CORP.

    The positive battery cable terminal AT the starter solenoid may be formed incorrectly. Incorrectly formed terminals CAN contact the starter solenoid housing…

  • 93V091000May 20 Anchorage · VOLVO GM HEAVY TRUCK CORP

    The safety belt buckle assembly CAN get caught in the seat suspension mechanism. The movement of the air suspension seat could cause the safety belt buckle…

  • 93V089000May 17 Transfer case (4-wheel drive) · FORD MOTOR COMPANY

    The transfer cases have been built with the wrong electric shift motor. The transfer cases CAN slip out of the 4 x 4 high gear position during coasting in…

  • 93V088000May 17 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    The fuel feed and return lines to the engine fuel injection system were not fully assembled and locked. The lines CAN work loose, causing a fuel leak in the…

  • 93V083000May 11 Switch · CHRYSLER CORPORATION

    Salt corrosion products between the starter solenoid wire and the adjacent battery feed in the bulkhead connector may short these connections, causing the…

  • 93V082000May 11 Antilock/traction control/electronic limited slip · CHRYSLER CORPORATION

    Some of the ABS equipped vehicles were built with an undersized brake return check valve. In incidents where hard brake pedal effort is applied on low friction…

April 1993

  • 93V074000Apr 28 Vehicle speed control · VOLVO CARS OF NA, INC.

    Plastic hood insulation clip(s) was(were) inadvertently dropped into the hose between the charge air cooler and the throttle housing which CAN interfere with…

  • 93V067000Apr 28 Power assist · MERCEDES-BENZ USA, INC.

    During the removal and installation of the air filter housing while servicing the vehicle, it is possible to misroute the preformed vacuum hose and damage the…

  • 93V073000Apr 27 Shock absorber · FORD MOTOR COMPANY

    The rear shock crossmember of the frame CAN crack and separate from the frame.

  • 93V072000Apr 27 Filler pipe and cap · SUBARU OF AMERICA, INC.

    The fuel filler system does not comply with the leakage requirements of fmvss 301, "fuel system integrity".

  • 93V066000Apr 27 Steering wheel/handle bar · FAIRMONT TAMPER

    Keys attached to the key ring of an ignition key while it is in the vehicle ignition CAN become lodged in the steering lock receiver as the steering wheel is…

  • 93V056000Apr 22 Anchorage · AMERICAN HONDA MOTOR CO.

    The rear outside seating position safety belts may lock up AT angles other than those required by fmvss 209, "seat belt assemblies". This does not conform to…

  • 93V057000Apr 15 Control module · FORD MOTOR COMPANY

    The roll pins securing the ignition lock in the steering column housing CAN separate or move out of position.

  • 93V058000Apr 13 Support device/strut · FORD MOTOR COMPANY

    Vehicle description: passenger vehicles. The lower pivot pin that joins the liftgate gas strut to the body CAN separate from the lower strut mounting bracket…

  • 93V055000Apr 8 Hatchback/liftgate · CHRYSLER CORPORATION

    Grease applied to the liftgate latch rubber bumpers to ease component assembly caused the bumper to swell, interfering with the movement of the liftgate latch…

  • 93V033001Apr 8 Driveline · CHRYSLER CORPORATION

    A condition exists that allows oil to leak from the all wheel drive transfer case. Low oil levels in the transfer case CAN cause bearing damage and failure.

  • 93V051000Apr 2 Suspension front · CHRYSLER CORPORATION

    The eccentric cam adjuster bolts in both front lower suspension arm-to-front axle bracket attachments may fail due to assembly misalignment.

March 1993

  • 93V033000Mar 26 Driveline · MITSUBISHI AMERICA

    A condition exists that allows oil to leak from the all wheel drive transfer case. Low oil levels in the transfer case CAN cause bearing damage and failure.

  • 93V041000Mar 19 Frontal · GENERAL MOTORS CORP.

    The passenger side air bag CAN experience an inflator ignition delay in the event of an accident. This does not comply with fmvss 208, "occupant crash…

  • 93V044000Mar 16 Anchorage · MITSUBISHI AMERICA

    The rear outboard lower safety belt attachment bolt was inadequately torqued on installation.

  • 93V037000Mar 9 Labels · CHRYSLER CORPORATION

    The tire and wheel specification information on the certification label indicates a minimum tire size larger than the tire actually fitted to the vehicle. This…

  • 93V035000Mar 9 Seats · GENERAL MOTORS CORP.

    The driver and passenger front seat manual reclining mechanisms do not comply with the requirements of fmvss 207, "seating systems." the seat back mechanisms…

February 1993

  • 93V018000Feb 9 Fuses and circuit breakers · GENERAL MOTORS CORP.

    System: electrical.vehicle description: seq 9c1 police cars in corrosion areas of the US and canada only. Note: vehicles originally sold or currently…

  • 93V016000Feb 1 Automatic transmission · GENERAL MOTORS CORP.

    Unanticipated heat in the transmission CAN force the transmission fluid out of the vent tube.

  • 93V015000Feb 1 Heater core · BAYERISCHE MOTOREN WERKE

    The malfunction or failure of a coolant system component results in significantly increased coolant temperature and a resulting increase in system pressure.

January 1993

  • 93V010000Jan 19 Delivery · GENERAL MOTORS CORP.

    The engine mounted fuel feed and return pipes may fracture due to contact with the engine frame during operation.

  • 93V008000Jan 14 Cooling system fan · GENERAL MOTORS CORP.

    The engine cooling fan blades break as a result of fatigue and/or vehicle induced stress.

  • 93V007000Jan 11 Vacuum · VOLKSWAGEN OF AMERICA,INC

    The blades in the brake vacuum booster pump CAN wear prematurely, causing reduced brake assist pressure when the brake pedal is applied.

  • 93V006000Jan 11 Axle assembly · VOLKSWAGEN OF AMERICA,INC

    The differential oil of the transaxle is lost over time due to evaporation. Low oil levels cause premature bearing and gear wear and eventual failure of the…

  • 93V023000Jan 4 Antilock/traction control/electronic limited slip · FORD MOTOR COMPANY

    Anti-lock brake system controllers designed for rear wheel drive cars may have been installed on these front wheel drive cars..