Car recalls in 1994
130 recall campaigns for the vehicles on this site were filed with NHTSA in 1994, covering about 5,223,527 vehicles.
December 1994
-
94V251000Dec 30
Caliper · NISSAN NORTH AMERICA, INC.
The right front brake caliper piston seal groove was improperly machined causing a brake fluid leak when the brakes are applied.
-
94V249000Dec 30
Linkages · JAGUAR CARS
The steering assembly was fitted with incorrect specification nuts. These nuts retain the track rod end ball pins to the steering arms.
-
94V248000Dec 23
Webbing · GENERAL MOTORS CORP.
Insufficient lubrication in the guide track rail in which the shoulder belt carrier moves causing a chattering noise, momentary binding while traveling,…
-
94V243000Dec 14
Doors latch · NISSAN NORTH AMERICA, INC.
Trucks were assembled without a door lock plate in the right side door.
-
94V244000Dec 12
Connection · FORD MOTOR COMPANY
The drag link installed CAN contact the front axle i-beam under certain extreme conditions. This drag link was not intended to be installed on "low profile"…
-
94V242000Dec 12
Pedals and linkages · GENERAL MOTORS CORP.
The brake pedal pivot bolt was started in the weld nut, but was not torqued correctly causing the bolt to disengage from the weld nut.
-
94V239000Dec 1
Carrier/rack · FORD MOTOR COMPANY
The spare tire supplied with the vehicle CAN contact the brake lines on the rear axle if it is mounted in the underbody spare tire carrier. Such contact could…
November 1994
-
94V235000Nov 28
Control unit/module · FORD MOTOR COMPANY
The vehicles were manufactured without separate ABS indicator lamps. This does not comply with the requirements of fmvss no. 105, "hydraulic brake systems."
-
94V230000Nov 21
Lower ball joint · GENERAL MOTORS CORP.
A right-hand lower control arm tapered ball joint mounting hole was incorrectly machined. Movement within this attachment CAN allow the ball joint stud to…
-
94V229000Nov 21
Exterior lighting · GENERAL MOTORS CORP.
The vehicles were assembled with an incorrect front park/turn signal bulb which does not have sufficient candle power. This does not comply with fmvss no. 108,…
-
94V228000Nov 21
Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.
A vacuum hose CAN detach from the power brake booster check valve as a result of engine backfire.
-
94V227000Nov 21
Labels · GENERAL MOTORS CORP.
Both the supplemental inflatable restraint (sir) caution label and an engine start label were installed on the same side of the driver's sun visor. This does…
-
94V226000Nov 18
Recliner · SAAB CARS USA, INC.
One or more of the arc welds CAN be missing on the seat back frame recliner.
-
94V218000Nov 10
Frontal · FORD MOTOR COMPANY
The driver side air bag module CAN have an inadequately welded inflator canister.
-
94V220000Nov 8
Wiring · TOYOTA MOTOR CO., LTD.
An unused harness connector for power windows, power door locks and sunroof was improperly routed under the floor carpet in the left kick panel. If the vehicle…
-
94V219000Nov 8
Doors latch · BAYERISCHE MOTOREN WERKE
The double-lock feature CAN engage with occupants and the door/ignition key inside the vehicle.
-
94V217000Nov 8
Pedal/hand lever(motorcycle) · GENERAL MOTORS CORP.
The automatic transaxle park lock cable assembly was improperly adjusted making it possible to shift from the "park" position with the ignition key removed, or…
-
94V223000Nov 4
Alternator/generator/regulator · FORD MOTOR COMPANY
The alternator output wire was not connected tightly to the power distribution box.
-
94V222000Nov 4
Front underhood · FORD MOTOR COMPANY
The wiring harness insulation CAN abrade on a brace that runs from the instrument panel to the cowl.
-
94V215000Nov 1
Frontal · VOLVO CARS OF NA, INC.
The driver's side air bag module may not properly deploy.
October 1994
-
94V169002Oct 31
Conventional · MAZDA (NORTH AMERICA),INC
The parking brake control self-adjust pawl does not line up properly with the self-adjust rachet causing the pawl to slip over one or more teeth in the rachet.
-
94V213000Oct 26
Foundation components drum · GENERAL MOTORS CORP.
The rear brake drums were not correctly machined. As the vehicle is driven, loss of wheel clamp load CAN result from this condition. Once clamp load is lost,…
-
94V212000Oct 26
Windshield · GENERAL MOTORS CORP.
The windshields were installed with incorrect windshield opening pinch-weld-flange primer. This primer will not properly etch the painted surface of the…
-
94V211000Oct 26
Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.
The brake lines CAN contact the transmission mounting bracket of the frame side rail. The lines CAN wear through resulting in loss of brake fluid, and eventual…
-
94V210000Oct 25
Mounting · GENERAL MOTORS CORP.
The fuel tank attachment strap fasteners were not properly tightened. The fasteners CAN completely detach, eventually allowing the fuel tank to sag and the…
-
94V203000Oct 18
Filler pipe and cap · FORD MOTOR COMPANY
The fuel tank filler pipe opening reinforcement CAN leak AT the weld.
-
94V202000Oct 18
Suspension front · CHRYSLER CORPORATION
The front suspension track bar bracket attachment has inadequate fatigue strength and CAN fail, causing front axle vibration.
-
94V199000Oct 13
Axle assembly · GENERAL MOTORS CORP.
The upper transaxle oil cooler hose CAN pull out of the crimped coupling AT the transaxle end of the line assembly.
-
94V198000Oct 11
Pedals and linkages · FORD MOTOR COMPANY
The retainer clip which holds the master cylinder push rod to the brake pedal arm is missing or not completely installed. The push rod CAN separate from the…
-
94V197000Oct 11
Frontal · FORD MOTOR COMPANY
Two bolts that attach the passenger side air bag supplemental restraint system module to the instrument panel are missing. In the event of a frontal impact,…
-
94V194000Oct 5
Wheels · NISSAN NORTH AMERICA, INC.
The aluminum wheels were clear coated several times to protect the metal finish. Some excessive coating CAN leave the wheel nuts an excessive distance from the…
-
94V190000Oct 4
Headlights · GENERAL MOTORS CORP.
These vehicles were assembled with lighting control modules which CAN experience excessive current leakage due to damaged surface mounting capacitors. This CAN…
-
94V189000Oct 4
Spindle arm · GENERAL MOTORS CORP.
The right hand spindle nut was not properly tightened during assembly. This CAN cause premature wheel bearing failure and over time, the spindle CAN fracture.
-
94V188000Oct 4
Mounting · GENERAL MOTORS CORP.
The fuel lines attached to the fuel tank were not properly tightened.
-
94V186000Oct 4
Delivery · FORD MOTOR COMPANY
The fuel supply, return and vapor hoses or lines CAN contact or have inadequate clearance with the surrounding components due to improper positioning during…
September 1994
-
94V184000Sep 29
Filler pipe and cap · FORD MOTOR COMPANY
A metal shield on the outside of the plastic fuel filler pipe CAN develop a static electrical charge during refueling of the vehicle.
-
94V176000Sep 20
Body door · GENERAL MOTORS CORP.
The reinforcement panel that serves as a liftpoint for the frame was omitted from the right side rocker assembly of the frame the vehicles do not conform to…
-
94V163000Sep 16
Linkage and cable · HOME & PARK MOTORHOMES
The parking brake cable is routed to the right rear wheel causing it to cross and contact the steel brake line. This CAN cause the abrasion and rupture of the…
-
94V177000Sep 14
Head restraint · SHERRY DESIGNS, INC.
The front driver and passenger seat back height does not conform to the requirements of fmvss no. 202, "head restraints."
-
94V174000Sep 14
Body door · SAAB CARS USA, INC.
The two weld points in the rearward attachment bracket for the side impact protection beam in the rear door may be out of position. If the welds are out of…
-
94V170000Sep 14
Gear box (other than rack and pinion) · GENERAL MOTORS CORP.
The steering gear pinion shaft was improperly heat treated causing the shaft to fracture during vehicle operation.
-
94V173000Sep 13
Vehicle speed control · VOLVO CARS OF NA, INC.
Under very cold weather conditions, ICE crystals CAN form AT the throttle in the engine intake system, and prevent the throttle from returning to idle.
-
94V169001Sep 7
Conventional · FORD MOTOR COMPANY
The parking brake control self-adjust pawl does not line up properly with the self-adjust rachet causing the pawl to slip over one or more teeth in the rachet.
-
94V165000Sep 2
Gear position indication (prndl) · NISSAN NORTH AMERICA, INC.
The shift lever lock plate, which prevents the shift lever from being inadvertently moved from park to drive or neutral position, CAN be broken by the…
-
94V166000Sep 1
Labels · HYUNDAI MOTOR AMERICA
The tire inflation pressure label affixed to the left rear door states that the vehicle capacity is "1,100 pounds". This information is incorrect. The correct…
-
94V164000Sep 1
Hoses, lines/piping, and fittings · AM GENERAL CORPORATION
The oil pressure switch which controls the power to the electric fuel pump CAN fail. Failure is due to a missing rubber seal between the switch and the wiring…
-
94V162000Sep 1
Hoses, lines/piping, and fittings · AM GENERAL CORPORATION
The passenger compartment is separated from the engine compartment by an insulated engine cover. The insulation inside this cover CAN rub against the fuel…
August 1994
-
94V159000Aug 31
Doors latch · GENERAL MOTORS CORP.
Water intrusion CAN cause a short circuit in the power door lock assembly.
-
94V158000Aug 31
Air conditioner · GENERAL MOTORS CORP.
If the air conditioner compressor clutch assembly contacts the auxiliary engine oil cooler out hose, the hose may wear through allowing engine oil to leak in…
-
94V155000Aug 16
Tires valve · AMERICAN HONDA MOTOR CO.
The tire valve stems were damaged during the assembly process. This CAN cause the tire to lose air pressure.
-
94V151000Aug 10
Anchorage · BAYERISCHE MOTOREN WERKE
In a fmvss no. 208 30 miles-per-hour compliance test, an unbelted test driver dummy's chest maximum resultant acceleration was 70.8 g's, which exceeds the…
-
94V152000Aug 9
Foundation components · FORD MOTOR COMPANY
The nuts and bolts that attach the rear brake adaptor to the axle housing flange CAN loosen and eventually separate. If one or more of the nuts come off the…
-
94V149002Aug 8
Antilock/traction control/electronic limited slip · MITSUBISHI AMERICA
The headlamp support panel CAN develop a fatigue crack where the anti-lock brake system (ABS) hydraulic unit is attached, allowing the hydraulic unit to fall…
-
94V149001Aug 8
Antilock/traction control/electronic limited slip · CHRYSLER CORPORATION
The headlamp support panel CAN develop a fatigue crack where the anti-lock brake system (ABS) hydraulic unit is attached, allowing the hydraulic unit to fall…
-
94V139000Aug 4
Seats · SHERRY DESIGNS, INC.
The factory mounted armrest on the driver and passenger door do not conform to the requirements of fmvss no. 201, "occupant protection in interior impact."
-
94V138000Aug 2
Switch · GENERAL MOTORS CORP.
A spring in the head lamp portion of the head park lamp switch CAN fail preventing latching of the head lamp portion of the switch in the "on" position.
-
94V142000Aug 1
Windshield · FORD MOTOR COMPANY
The windshields were marked with a "prototype" designation and not marked as required by fmvss no. 205, "glazing materials."
-
94V141000Aug 1
Labels · FORD MOTOR COMPANY
The dates of manufacture were omitted on the certification label. This does not comply with part 567, "certification."
July 1994
-
94V135000Jul 25
Brake fluid low warning lamp · NISSAN NORTH AMERICA, INC.
The instrument panel brake warning light will not illuminate when the brake fluid level in the master cylinder drops sufficiently to activate the low level…
-
94V134000Jul 25
Power train · KIA MOTORS AMERICA, INC.
The electronic speedometer sensor CAN seize, causing the speedometer and cruise control (if the car is equipped with cruise control) to stop functioning.
-
94V132000Jul 19
Engine · ISUZU MOTORS LIMITED
Constant expansion and contraction of the cylinder head causes the camshaft seal end plug CAN become dislodged from the cylinder head. This allows oil to leak…
-
94V129000Jul 12
Pedals and linkages · FORD MOTOR COMPANY
The brake pedal push rod retainer (hairpin clip) may be missing or not properly installed on the service brake pedal. This CAN cause disengagement of the brake…
-
94V128000Jul 11
Interior lighting · MARK III INDUSTRIES, INC.
The transformer used to power the neon center lightbeam CAN overheat and catch on fire.
-
94V127000Jul 8
Seats · SAAB CARS USA, INC.
Two trigger springs mounted to the fore/aft adjustment lever do not develop sufficient force to properly lock the seat rails. After the seat is adjusted, this…
-
94V126000Jul 8
Cooling system · SAAB CARS USA, INC.
During low energy frontal impact collisions, the front crossmember CAN contact the metal tubing portion of the cooler hose assembly; and/or the hose assembly…
-
94V125000Jul 7
Lower arm · GENERAL MOTORS CORP.
The lower control arm CAN crack AT the flange on the end of the control arm near the ball joint pad.
-
94V122000Jul 1
Tank assembly · GENERAL MOTORS CORP.
These vehicles were constructed with welds in the rear compartment pan assembly that are not sufficient to comply with the requirements pertaining to fuel tank…
June 1994
-
94V118000Jun 27
Rack and pinion · FORD MOTOR COMPANY
The steering gears have an improperly machined snap ring groove. This CAN cause a fracture of the snap ring with subsequent damage to the recirculating ball…
-
94V117000Jun 24
Owners/service/other manual · GENERAL MOTORS CORP.
These vehicles were shipped with the wrong owner's manual, and, therefore, the correct information regarding safety belt usage is not available to the owner.…
-
94V115000Jun 24
Spindle arm · GENERAL MOTORS CORP.
These vehicles were built with overtorqued drive axle spindle nuts. This condition CAN cause excessive loads on the spindle nut and drive axle resulting in…
-
94V114000Jun 20
Trailer hitches · GENERAL MOTORS CORP.
The trailer hitch attaching bolts were not tightened to the specified torque. This CAN lead to loosening and subsequent breakage of the fasteners.
-
94V113000Jun 20
Fuel system, gasoline · CHRYSLER CORPORATION
These vehicles do not meet the rear impact test requirements of fmvss 301, "fuel system integrity."
-
94V111002Jun 13
Hoses, lines/piping, and fittings · MAZDA (NORTH AMERICA),INC
The front fuel lines have a section of flexible hose that is susceptible to cracking which CAN allow fuel leakage.
-
94V111001Jun 13
Hoses, lines/piping, and fittings · FORD MOTOR COMPANY
The front fuel lines have a section of flexible hose that is susceptible to cracking which CAN allow fuel leakage.
-
94V110000Jun 13
Seats · SAAB CARS USA, INC.
A weld in the seat rails was not made, increasing the risk of fatigue cracks forming around the attachment bushings on the height adjustment mechanism, causing…
-
94V108000Jun 9
Switch · SAAB CARS USA, INC.
A number of brake light switches have an oval-shaped piston which CAN get stuck under certain conditions. Other switches were mounted so that both locking tabs…
-
94V106000Jun 9
Fuel pump · CHRYSLER CORPORATION
Vehicle description: multipurpose passenger vehicles equipped with plastic fuel tanks. The fuel tank sending unit gasket CAN crack causing fuel and fuel vapor…
May 1994
-
94V101000May 25
Module · FORD MOTOR COMPANY
In a heavily loaded vehicle, while in the cruise control mode, the throttle may not reduce immediately when the load on the engine is decreased (such as when…
-
94V100000May 24
Webbing · GENERAL MOTORS CORP.
The second row, right hand shoulder belt CAN become "pinched" between the seat and the door frame pillar trim. The shoulder belt may not retract properly,…
-
94V097000May 20
Suspension front · CHRYSLER CORPORATION
The front suspension track bar has inadequate fatigue strength.
-
94V093000May 16
Automatic transmission · GENERAL MOTORS CORP.
Significant wear CAN develop on the low and reverse clutch preventing the park pawl from engaging. This CAN prevent a "no park" condition to occur while the…
-
94V091000May 13
Vehicle speed control · MERCEDES-BENZ USA, INC.
The factory installed cruise control linkage may not have been adequately lubricated, which CAN cause binding and the throttle will not return to the closed…
-
94V094000May 11
Cooling system · MAZDA (NORTH AMERICA),INC
The radiator cap pressure relief valve release pressure is set too high. This CAN cause the coolant to reach temperatures that exceed the thermal design limits…
-
94V090000May 11
Alternator/generator/regulator · HYUNDAI MOTOR AMERICA
In some vehicles, the manufacturer's protective internal coating of the electronic crank angle sensor does not meet specifications, which CAN cause an open…
-
94V087000May 9
Labels · EXPLORER VAN COMPANY
The manufacturer's certification label and/or the driver air bag advisory label may be missing from the vehicles, which does not conform to the requirements of…
-
94V088000May 6
Windshield wiper/washer motor · PORSCHE CARS N.A. INC.
The plastic cowl cover was not sealed to the body AT the base of the windshield. Water CAN leak and reach the windshield wiper motor, causing internal…
-
94V085000May 3
Hoses, lines/piping, and fittings · ISUZU MOTORS LIMITED
On some vehicles, the sealing surfaces for a hydraulic brake hose on a front brake caliper were covered by paint residue. Brake fluid gradually dissolves the…
-
94V084000May 2
Brake lights · SAAB CARS USA, INC.
One of the bulbs in each of the brake light lower outboard lamp assemblies may not have been properly wired, resulting in improper tail light illumination on…
April 1994
-
94V077000Apr 25
Filler pipe and cap · GENERAL MOTORS CORP.
The fuel filler neck solder joint CAN develop cracks or pin hole leaks, which does not comply with fmvss no. 301, "fuel system integrity." the cracks and holes…
-
94V080000Apr 20
Fuel system, gasoline · MITSUBISHI AMERICA
The vehicles failed the lateral moving barrier impact test requirements of fmvss 301, "fuel system integrity." the fuel leakage from the gas tank exceeded the…
-
94V076000Apr 16
Lugs/nuts/bolts/studs · GENERAL MOTORS CORP.
Paint on the wheel mounting surfaces CAN act as a shim between the wheel and the rotor/drum. As the vehicle is driven, the wheel imbeds into the paint,…
-
94V074000Apr 16
Foundation components disc · SAAB CARS USA, INC.
The original front brake discs and/or pads shields do not protect the assemblies from being coated with a layer of slush, road salt or water while driving in…
-
94V073002Apr 16
Suspension rear · AMERICAN SUZUKI MOTOR CORP.
The right rear and left axle shaft housing tubes were incorrectly welded and CAN fracture. Fracture of the rear axle shaft housing CAN result in separation of…
-
94V073001Apr 16
Suspension rear · GENERAL MOTORS CORP.
The right rear and left axle shaft housing tubes were incorrectly welded and CAN fracture. Fracture of the rear axle shaft housing CAN result in separation of…
-
94V066000Apr 11
Hoses, lines/piping, and fittings · BAYERISCHE MOTOREN WERKE
Feed fuel hoses CAN harden and "set" over time, allowing a seepage of fuel AT the connection between the hose and the engine fitting. The clamp used to hold…
-
94V063000Apr 10
Automatic transmission · AMERICAN HONDA MOTOR CO.
A retaining clip that connects the transmission shift cable to the shift lever actuating rod CAN have insufficient retention pressure and may eventually come…
-
94V064000Apr 7
Delivery · PEUGEOT, INC.
The fuel supply line CAN come in contact with a high voltage ignition lead in the engine compartment, causing deterioration of the fuel line over time. The…
-
94V060000Apr 5
Lower arm · GENERAL MOTORS CORP.
Trucks were assembled with the left-hand lower control arm to frame rear nut tightened below the specified torque. Low torque on this nut may allow the…
-
94V044001Apr 5
Tank assembly · GENERAL MOTORS CORP.
Vehicles altered by pas, inc. Have compressed natural gas fuel tanks that CAN develop stress corrosion, which crack the e-glass wrapping. This stress corrosion…
-
94V058000Apr 4
Steering wheel/handle bar · VOLKSWAGEN OF AMERICA,INC
These steering wheels and include a universal joint which is attached to steering shafts and secured by locking bolts. The universal joint's upper locking bolt…
March 1994
-
94V056000Mar 26
12v/24v/48v battery · FORD MOTOR COMPANY
System: electrical system; battery. Vehicle description: medium duty school bus chassis equipped with hydraulic brakes, tilt hoods, 5.9l, 6.6l or 7.6l diesel…
-
94V055000Mar 26
Seats · FORD MOTOR COMPANY
The lock plate of the driver side inboard seat track adjusters were manufactured with an unauthorized modification to the fabrication process which causes the…
-
94V053000Mar 23
Wheels · GENERAL MOTORS CORP.
These vehicles were equipped with incorrect spare wheels. The use of an incorrect spare wheel in a mounted position CAN, under certain load conditions,…
-
94V052000Mar 23
Manual transmission · SUBARU OF AMERICA, INC.
When the vehicle is driven continuously under extremely cold temperatures (-22 degrees f.) and high humidity weather conditions, the transmission breathing…
-
94V049000Mar 21
Hoses/lines/piping/fittings · GENERAL MOTORS CORP.
The engine oil cooler inlet hose may have been installed too close to the steering gear causing chafing. The chafing CAN eventually wear through the hose's…
-
94V043000Mar 9
Control arm · CHRYSLER CORPORATION
Some upper control arm attaching bolts CAN fail due to improper heat treatment. The bolts are too soft to withstand the stresses in the steering system and CAN…
February 1994
-
94V035000Feb 28
Vehicle speed control · NISSAN NORTH AMERICA, INC.
Engine movement CAN be transmitted to the airflow meter/filter housing and support bracket, which is mounted in the engine air duct, causing the throttle cable…
-
94V040000Feb 23
Hoses, lines/piping, and fittings · FORD MOTOR COMPANY
The steel fuel return tubes that connect the frame fuel return lines with the engine fuel rail CAN contact the pinch weld flange connecting the dash panel to…
-
94V039000Feb 23
Hood latch · TOYOTA MOTOR CO., LTD.
The secondary hood latch mechanism has a narrow clearance between internal parts which, over time, accumulate dust or other foreign matter and cause the latch…
-
94V034000Feb 23
Hoses, lines/piping, and fittings · CHRYSLER CORPORATION
The rear brake hose mounting bracket screws CAN fail allowing the brake hoses to move out of position. The unrestrained hoses are then susceptible to damage…
-
94V033000Feb 23
Power train · CHRYSLER CORPORATION
Moisture CAN get into the powertrain control module (PCM) causing driveability malfunctions, including stalling.
-
94V037000Feb 17
Fuel injection system · BAYERISCHE MOTOREN WERKE
The adhesive material of the two piece throttle body heater migrates into the circulation chamber causing build up of impurities and restriction of flow within…
-
94V024000Feb 8
Wiring · CHRYSLER CORPORATION
The right steering tie rod CAN rub through the automatic transmission wiring harness causing a short circuit which results in electrical system malfunctions…
-
94V023000Feb 8
Anchorage · CHRYSLER CORPORATION
The safety belt anchors (buckle lock bars) do not meet the static load requirements of fmvss no. 210, "seat belt assembly anchorages."
-
94V029000Feb 3
Fuel system, gasoline · SAAB CARS USA, INC.
The fuel filler and tank ventilation hoses may develop cracks under the securing hose clamps, resulting in fuel leakage.
January 1994
-
94V017000Jan 27
Power window devices and controls · BAYERISCHE MOTOREN WERKE
The remote activation device CAN close windows and sunroof from a distance greater than the maximum (6 meters) permitted by fmvss no.118, "power operated…
-
94V014000Jan 26
Filler pipe and cap · GENERAL MOTORS CORP.
The fuel tank filler pipes were not manufactured to specification which caused loss of fuel between the fuel tank filler pipe and the vent tube during a test.…
-
94V016000Jan 21
Rack and pinion · GENERAL MOTORS CORP.
These vehicles were assembled with a lower steering shaft that CAN separate due to a mislocated weld.
-
94V015000Jan 21
Retractor · GENERAL MOTORS CORP.
The third row safety belt retractors may be installed incorrectly and may lock-up when the vehicle is on slopes of less than 15 degrees, which does not comply…
-
94V008000Jan 12
Springs · GENERAL MOTORS CORP.
In the event of a primary accelerator control spring failure, the secondary (back-up) accelerator control return spring will not return the throttle to the…
-
94V007000Jan 12
Frontal · NISSAN NORTH AMERICA, INC.
In some underbody impacts the airbag sensor activates and sends a signal to the airbag, located in the center of the steering wheel, causing the driver's side…
-
94V005000Jan 12
Mounting · CHRYSLER CORPORATION
Two fuel tank support strap attaching studs were not adequately tightened, which could cause one or both of the strap(s) to separate, mislocating the fuel…
-
94V006000Jan 11
Heater core · CHRYSLER CORPORATION
The end cap connecting the heat exchanger's core to the engine cooling system could rupture and allow hot coolant to escape into the passenger compartment.
-
94V026000Jan 9
Antilock/traction control/electronic limited slip · CHRYSLER CORPORATION
The ABS brake master cylinder rear seal allows air to enter the brake system, causing spongy brakes or partial brake system loss.
-
94V028000Jan 8
Gear box (other than rack and pinion) · GENERAL MOTORS CORP.
The intermediate steering shaft was assembled with loose or missing upper and lower pinch bolts which may cause separation of the shaft.
-
94V021000Jan 8
Cables · GENERAL MOTORS CORP.
During assembly, water may have entered the accelerator control cable conduit causing it to develop a high effort and/or binding condition in very cold weather.
-
94V004000Jan 6
Exhaust system · MERCEDES-BENZ USA, INC.
High ambient engine compartment temperatures are experienced after the vehicle is operated and then parked. If the vehicle is restarted a short time later and…
-
94V027000Jan 4
Rear/other · GENERAL MOTORS CORP.
Vehicle fails to conform to fmvss no. 209, "seat belt assemblies." the safety belt of the left third row seat on the six passenger van and the center second…
-
94V022000Jan 3
Cables · BAYERISCHE MOTOREN WERKE
The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.
-
94V018000Jan 2
Bumpers · FORD MOTOR COMPANY
The u-clip style nuts that retain the front bumpers to the front bumper inner arms CAN fracture.