Recalls filed in 1995

Car recalls in 1995

126 recall campaigns for the vehicles on this site were filed with NHTSA in 1995, covering about 17,966,938 vehicles.

December 1995

  • 95V248000Dec 28 Cooling system · PORSCHE CARS N.A. INC.

    The inside pipes of the heat exchangers might be subject to cracking.

  • 95V247000Dec 28 Manifold/header/muffler/tail pipe · PORSCHE CARS N.A. INC.

    The cover sleeves on the exhaust tailpipes have been secured with only two instead of four welding spots.

  • 95V243000Dec 28 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    Certain trucks have fuel rail assemblies with an improperly crimped end retainer clip that results in a fuel leak.

  • 95V246000Dec 21 Seats · GENERAL MOTORS CORP.

    The seat recliner to seat frame attaching bolts on these vehicle could loosen, fatigue and fracture, allowing the seat back to suddenly recline.

  • 95V231002Dec 20 Vehicle speed control · MAZDA (NORTH AMERICA),INC

    During extreme cold, northern climate winter conditions, ICE CAN form in the throttle body of the engine causing the throttle plate to remain in the highway…

  • 95V244000Dec 15 Filler pipe and cap · NISSAN NORTH AMERICA, INC.

    It is possible for a mixture of mud and salt to get trapped between the fuel filler tube and wheel housing. The trapped mud and salt CAN result in corrosion of…

  • 95V242000Dec 13 Seat belts front · GENERAL MOTORS CORP.

    These vehicles were built with front seat belt systems with no energy management loops and may not meet the head injury criteria requirements of fmvss no. 208,…

  • 95V241000Dec 13 Seat belts front · GENERAL MOTORS CORP.

    If both the lap-belt and shoulder-belt energy management loops on the front seat belt assemblies release AT or near the same time, acceleration forces CAN…

  • 95V237000Dec 12 Alternator/generator/regulator · CHRYSLER CORPORATION

    The fasteners which secure the generator cartridge fuse to the power distribution center may have an improper clamp load. Improper clamping CAN result in…

  • 95V238000Dec 11 Hoses, lines/piping, and fittings · BAYERISCHE MOTOREN WERKE

    Fuel seepage CAN occur between a hose and the metal fuel line on either end of the hose resulting in fuel odor.

  • 95V236000Dec 8 Hoses, lines/piping, and fittings · CHRYSLER CORPORATION

    The fuel tank rollover valve CAN allow fuel to pass into the vapor canister resulting in the potential for fuel leakage.

  • 95V233000Dec 8 Suspension · VOLVO GM HEAVY TRUCK CORP

    The tilt cab, when raised to its fullest up position, CAN cause the steering shaft to bind against the steering gear.

  • 95V232000Dec 5 Filler pipe and cap · FORD MOTOR COMPANY

    The fuel tank filler pipe opening reinforcement, constructed from two separately molded pieces, CAN leak AT the weld.

  • 95V231001Dec 5 Vehicle speed control · FORD MOTOR COMPANY

    During extreme cold, northern climate winter conditions, ICE CAN form in the throttle body of the engine causing the throttle plate to remain in the highway…

  • 95V230000Dec 5 Service brakes, hydraulic fluid · ROLLS-ROYCE MOTORS, INC.

    An incompatibility CAN exist between the mineral oil supplied by castrol and the hydraulic brake system of these vehicles.

  • 95V229000Dec 5 Hinge and attachments · GENERAL MOTORS CORP.

    These vehicles could have been produced with an improperly adjusted secondary hood latch. This does not conform to the requirements of fmvss no. 113, "hood…

  • 95V228000Dec 4 Anchorage · FORD MOTOR COMPANY

    Cracks have been found in the front safety belt outboard anchor tabs due to a combination of hydrogen embrittlement of the tab and stress introduced during…

November 1995

  • 95V224000Nov 30 Electrical · GENERAL MOTORS CORP.

    The analog instrument panel cluster on these vehicles could have an internal short circuit disrupting the pass key system, causing failure of the instrument…

  • 95V225000Nov 28 Seats · CHRYSLER CORPORATION

    The bolts which secure the rear bench seats to the seat risers may be embrittled and fracture.

  • 95V222002Nov 22 Defroster/defogger/HVAC system · NISSAN NORTH AMERICA, INC.

    Leaves and other foreign material CAN enter through the cowl panel air intake during operation of the front heater and/or air conditioning system resulting in…

  • 95V222001Nov 21 Defroster/defogger/HVAC system · FORD MOTOR COMPANY

    Leaves and other foreign material CAN enter through the cowl panel air intake during operation of the front heater and/or air conditioning system resulting in…

  • 95V221000Nov 16 Automatic transmission · GENERAL MOTORS CORP.

    These vehicles were produced with an improperly adjusted transmission shift control linkage. This does not meet with the requirements of fmvss no. 114, "theft…

  • 95V218000Nov 13 Controls, pedals and linkages · VOLVO GM HEAVY TRUCK CORP

    Undercoating applied to the inside of the cab shell squeezed out during assembly onto the brake pedal plunger.

  • 95V213000Nov 7 Anchorage · CHRYSLER CORPORATION

    The automatic shoulder belt systems CAN malfunction and become inoperative.

  • 95V215000Nov 3 Air bags · GENERAL MOTORS CORP.

    These vehicles were shipped with both the supplemental inflatable restraint caution label and a roof rack caution label installed on the same side of the sun…

  • 95V214000Nov 3 Vehicle speed control · GENERAL MOTORS CORP.

    These vehicles were assembled with throttle cable support brackets that could contact the throttle lever system and inhibit the throttle return. This does not…

October 1995

  • 95V203000Oct 24 Frontal · AMERICAN HONDA MOTOR CO.

    The passenger air bag was improperly installed. The retainer tabs used to secure the lower module to the upper housing were drilled incorrectly.

  • 95V204000Oct 23 Control module · GENERAL MOTORS CORP.

    These vehicles were assembled with a malfunction alarm, lighting and locking (mall) module that CAN contain a damaged capacitor. If the capacitor is damaged,…

  • 95V201000Oct 23 Vehicle speed control · GENERAL MOTORS CORP.

    The accelerator control cable could have been kinked during assembly causing high accelerator pedal effort, sticking accelerator control cable, or a broken…

  • 95V199000Oct 20 Power assist · CHRYSLER CORPORATION

    The power brake booster vacuum hose could be improperly installed and not clamped to the brake booster vacuum nipple.

  • 95V197000Oct 17 Doors latch · GENERAL MOTORS CORP.

    These vehicles were built with a sliding side-door rear latch that was improperly riveted. This does not meet the requirements of fmvss no. 206, "door locks…

  • 95V195002Oct 11 12v/24v/48v battery · GENERAL MOTORS CORP.

    The battery CAN have a defective weld inside the positive and/or negative terminal allowing the connection inside of the terminal to separate.

  • 95V195001Oct 11 12v/24v/48v battery · TOYOTA MOTOR CO., LTD.

    The battery CAN have a defective weld inside the positive and/or negative terminal allowing the connection inside the terminal to separate.

  • 95V194000Oct 11 Upper arm · FORD MOTOR COMPANY

    The bolts that attach the front upper control arms to the frame mounting brackets CAN loosen and fracture AT one of the bolt holes causing substantial negative…

  • 95V193000Oct 11 Fuses and circuit breakers · CHRYSLER CORPORATION

    The fasteners which secure the alternator circuit fuse to the power distribution center may have an improper clamp load.

  • 95V192000Oct 11 Suspension rear · BAYERISCHE MOTOREN WERKE

    The lower suspension arm mounting eye on the right side rear axle hub carrier was produced with a casting flaw.

  • 95V186000Oct 3 Wheels rim · AUTOMOBILI LAMBORGHINI

    The rear of the wheel center section was painted causing a loss of friction between the wheel center piece and the flange (backing plate) enabling the flange…

  • 95V184000Oct 3 Air bags · MAZDA (NORTH AMERICA),INC

    The tie down hooks CAN cause undercarriage impacts that CAN result in unnecessary air bag deployments.

  • 95V189000Oct 2 Fuses and circuit breakers · FORD MOTOR COMPANY

    These vehicles were built with the non-cycling power window circuit breaker and the cycling headlamp circuit breaker interchanged.

September 1995

  • 95V180000Sep 22 Cooling system fan · GENERAL MOTORS CORP.

    Fan blade rivet breakage CAN occur causing the fan blade to separate from the spider.

  • 95V178000Sep 20 Cooling system fan · VOLKSWAGEN OF AMERICA,INC

    Improper material was used in manufacturing the radiator fan motor shaft causing the shaft to wear and become noisy.

  • 95V173000Sep 15 Anchorage · GENERAL MOTORS CORP.

    These vehicles were assembled with rear outboard safety belt anchorages that may not withstand the required load. This does not comply with fmvss no.210, "seat…

  • 95V175000Sep 13 Lower arm · GENERAL MOTORS CORP.

    These vehicles were assembled with the left-hand lower control arm-to-frame rear nut not tightened to the specified torque.

  • 95V172000Sep 12 Mechanical · CHRYSLER CORPORATION

    The parking brake handle release button CAN separate from the parking brake handle assembly, causing the parking brake to be inoperative.

August 1995

  • 95V164002Aug 28 Support device/strut · MAZDA (NORTH AMERICA),INC

    The hydraulic lift cylinders are attached to brackets that are welded to the liftgate. The bracket welds CAN fracture.

  • 95V164001Aug 25 Support device/strut · FORD MOTOR COMPANY

    The hydraulic lift cylinders are attached to brackets that are welded to the liftgate. The bracket welds CAN fracture.

  • 95V163000Aug 23 Shock absorber · HYUNDAI MOTOR AMERICA

    One or both of the rear suspension lower spring seats are not securely attached to the shock absorber and CAN slide lower onto the shock absorber than…

  • 95V161000Aug 18 Tank assembly · AM GENERAL CORPORATION

    Under high ambient temperatures (greater than 95 degrees fahrenheit) and the fuel tank level between 1/4 and 1/2 full, the fuel tank internal pressure CAN…

  • 95V160000Aug 17 Seats · ROLLS-ROYCE MOTORS, INC.

    Both front seat belt lower anchorage rails have a manufacturing weakness which could fracture in a vehicle impact.

  • 95V159000Aug 17 Automatic transmission · ROLLS-ROYCE MOTORS, INC.

    An incorrectly positioned wire within the electrically operated gearbox actuator CAN chafe against the cover causing the transmission selector fuse to blow.

  • 95V157000Aug 11 Engine · RANGE ROVER NA., INC.

    The idler pulley, part of the engine front end serpentine belt system, CAN fail resulting in serpentine belt damage or disengagement.

  • 95V155000Aug 11 Tank assembly · RANGE ROVER NA., INC.

    The bottom of the fuel tank CAN corrode over time allowing fuel to leak.

  • 95V152000Aug 8 Exterior lighting · GENERAL MOTORS CORP.

    Incorrect clear front side marker bulbs were installed rather than amber bulbs. This does not conform to the requirements of fmvss no. 108, "lamps, reflective…

  • 95V151000Aug 7 Hood latch · FORD MOTOR COMPANY

    The secondary hood latch may not engage when the hood is closed.

  • 95V158000Aug 4 Headlights · GENERAL MOTORS CORP.

    The driver side headlamp lens has an incorrect aim pad number on the lens. This does not comply with fmvss no. 108, "lamps, reflective devices, and associated…

  • 95V143000Aug 2 Vehicle speed control · FORD MOTOR COMPANY

    The hand throttle cable CAN wear the brass swivel block on the governor lever through which it passes.

July 1995

  • 95V141000Jul 26 Frame and members · GENERAL MOTORS CORP.

    Some welds were omitted from the body lock pillar, or "b" pillar. This does not comply with fmvss no.208, "occupant crash protection."

  • 95V139000Jul 26 Automatic transmission · GENERAL MOTORS CORP.

    The transmission shift-cable lock clip CAN back out of its installed position resulting in a loss of cable adjustment. When the shift lever is placed in the…

  • 95V140000Jul 25 Air bags · GENERAL MOTORS CORP.

    The vehicles have both the supplemental inflatable restraint (sir) label and an engine start label installed on the same side of the sun visor. This does not…

  • 95V134000Jul 17 Tie rod assembly · FORD MOTOR COMPANY

    The affected vehicles were built with outer tie rod ends with incorrect taper ball studs. The incorrect tapered ball studs CAN fracture within 50,000 miles.

  • 95V133000Jul 11 Hoses, lines/piping, and fittings · DABRYAN COACH BUILDERS

    Improper installation of the rear brake line AT the point AT which the extended brake line first bends and extends over the left rear wheel area of the frame.…

  • 95V103010Jul 6 Buckle assembly · DAIHATSU AMERICA, INC.

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V130000Jul 5 Back up lights · GENERAL MOTORS CORP.

    These vehicles were assembled with a transmission reverse signal switch that could leak causing loss of electrical contact when the transmission is in reverse.…

June 1995

  • 95V103011Jun 27 Buckle assembly · FORD MOTOR COMPANY

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V123000Jun 16 Hoses, lines/piping, and fittings · RANGE ROVER NA., INC.

    A flexible brake hose that connects the hydraulic pump to the anti-lock brake system (ABS) valve block assembly CAN leak causing loss of brake fluid.

  • 95V119000Jun 7 Idler and attachment · VOLVO GM HEAVY TRUCK CORP

    Two bolts attaching the upper steering arm to the front steering axle were not tightened properly.

  • 95V115000Jun 5 Wheels · GENERAL MOTORS CORP.

    Cracks develop in the wheel mounting surface. If these cracks become severe enough, the wheel will completely separate from the vehicle.

May 1995

  • 95V110000May 31 Webbing · GENERAL MOTORS CORP.

    The front outer shoulder belt web sew stop CAN become stuck in the retractor. The belt CAN be difficult to pull out of the retractor and some occupants may not…

  • 95V108000May 26 Power adjust · VOLVO CARS OF NA, INC.

    The threaded insert which attaches the safety belt catch to the front seat was incorrectly manufactured.

  • 95V103009May 24 Buckle assembly · ISUZU MOTORS LIMITED

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103008May 24 Buckle assembly · AMERICAN SUZUKI MOTOR CORP.

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103007May 24 Buckle assembly · GENERAL MOTORS CORP.

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103006May 24 Buckle assembly · SUBARU OF AMERICA, INC.

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103005May 24 Buckle assembly · MAZDA (NORTH AMERICA),INC

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103004May 24 Buckle assembly · MITSUBISHI AMERICA

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103003May 24 Buckle assembly · CHRYSLER CORPORATION

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103002May 24 Buckle assembly · NISSAN NORTH AMERICA, INC.

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V103001May 24 Buckle assembly · AMERICAN HONDA MOTOR CO.

    The front safety belt buckle release buttons CAN break. These red plastic release buttons are marked "press." if a button breaks, pieces CAN fall into the…

  • 95V101000May 24 Frontal · HYUNDAI MOTOR AMERICA

    The driver's side air bag was improperly assembled and could cause the air bag warning light to illuminate from increased electrical resistance.

  • 95V105000May 23 Cooling system · VOLKSWAGEN OF AMERICA,INC

    In the event of a cooling system component failure while the vehicle is driven, the coolant CAN overheat causing the cooling system pressure to rise to a level…

  • 95V099000May 16 Axle assembly · RANGE ROVER NA., INC.

    AT port of entry, a quality overcheck of the differential pinion shaft torque was performed. This check required the removal of the driveshafts. When the…

  • 95V091000May 16 Hood latch · FORD MOTOR COMPANY

    Corrosion of the hood latch striker plate causes detachment of the plate from the hood assembly resulting in an unexpected opening of the hood while the…

  • 95V095000May 12 Vehicle speed control · FORD MOTOR COMPANY

    Friction between the accelerat0r lever and the automatic transmission modulator lever CAN result in interference between the two levers which could prevent the…

  • 95V089000May 12 Steering wheel/handle bar · CHRYSLER CORPORATION

    The steering wheel armature stamping CAN crack due to fatigue and separate from the center hub attachment to the steering column.

  • 95V088000May 12 Steering wheel/handle bar · CHRYSLER CORPORATION

    While making a turn, the extra keys on a vehicle operator's key ring CAN become temporarily lodged in the screw access holes in the back cover of the steering…

  • 95V092000May 9 Wiring · FORD MOTOR COMPANY

    A connector in the wiring where the tilt hood mounted lamps attach to the vehicle wiring harness was built without sealing plugs. Moisture, road salt or other…

  • 95V086000May 1 Air bags · ALFA ROMEO, INCORPORATED

    The supplemental inflatable restraint caution label was not placed on the driver's sun visor. This does not meet the requirements of fmvss no. 208, "occupant…

April 1995

  • 95V082000Apr 24 Springs · GENERAL MOTORS CORP.

    These vehicles fail to conform to fmvss no. 124, "accelerator control systems." AT low temperatures, excessive friction CAN occur in the accelerator pedal…

  • 95V081000Apr 24 Rear/other · GENERAL MOTORS CORP.

    Vehicles fail to conform to fmvss no. 210, "seat belt anchorages." the center rear seat lap belt was improperly routed.

  • 95V080000Apr 24 Upper ball joint · GENERAL MOTORS CORP.

    The upper ball joint nuts were under-torqued resulting in improper seating in the steering knuckle.

  • 95V079000Apr 20 Electrical system horn · FERRARI NORTH AMERICA

    The international horn emblem is missing from the leather steering wheel cover. This does not meet the requirements for fmvss no. 101, "controls and displays."

  • 95V073000Apr 11 Suspension rear · KIA MOTORS AMERICA, INC.

    The nuts attaching the rear axle bearing oil seal retainers and brake backing plates to the rear axle housing may be under- torqued causing these units to…

  • 95V072000Apr 3 Lower ball joint · TOYOTA MOTOR CO., LTD.

    The spherical portions of certain lower ball joints had finished surfaces that were not smooth causing friction with the surface of the ball joint cap.

  • 95V071000Apr 3 Labels · BAYERISCHE MOTOREN WERKE

    An overstatement was made of the vehicle load capacity and designated seating capacity on the tire information placard. This does not meet the requirements of…

  • 95V070000Apr 3 Service brakes, hydraulic · ROLLS-ROYCE MOTORS, INC.

    The lower steering column linkage heat shield CAN come in contact with a brake hydraulic system pipe mounted to the engine assembly, eventually resulting in a…

March 1995

  • 95V069000Mar 30 Hoses, lines/piping, and fittings · MAZDA (NORTH AMERICA),INC

    Residual engine heat CAN cause premature deterioration of the fuel hose causing the hose to leak. Also, removing and reinstalling the deteriorated fuel hoses…

  • 95V068000Mar 29 Manual transmission · SAAB CARS USA, INC.

    It is possible to move the shift lever into the reverse gear position, remove the ignition key, and still have the transmission in neutral, or, to accidently…

  • 95V067000Mar 29 Control unit/module · SAAB CARS USA, INC.

    Moisture CAN follow the electrical harness and enter the pressure switch connector causing corrosion and malfunction of the switch.

  • 95V066000Mar 29 Module · SAAB CARS USA, INC.

    Upon startup, a voltage drop to the engine control module CAN cause a malfunction where engine speed fluctuates from 600 to 3,000 RPM for up to 30 seconds…

  • 94V041000Mar 28 Wheels · GENERAL MOTORS CORP.

    Cracks develop in the wheel mounting surface. If these cracks become severe enough, the wheel will completely separate from the vehicle.

  • 95V063000Mar 27 Filler pipe and cap · FORD MOTOR COMPANY

    The seal material between the fuel filler pipe and fuel tank may not have been fully cured during the molding process which could allow for fuel leakage.

  • 95V062000Mar 27 Seats · FORD MOTOR COMPANY

    The wire harness on these seats is banded to the front seat cushion supports. The end of one of the supports CAN puncture the harness, resulting in a high…

  • 95V061000Mar 22 Hoses, lines/piping, and fittings · GENERAL MOTORS CORP.

    The rear wheel brake hose(s) CAN contact the rear suspension components causing the brake hose(s) to wear through.

  • 95V058000Mar 22 Linkage and cable · FORD MOTOR COMPANY

    The parking brake front cables were built longer than appropriate that reduces the performance of the parking brake in certain circumstances, and fails to…

  • 95V046000Mar 22 Gear box (other than rack and pinion) · GENERAL MOTORS CORP.

    The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.

  • 95V057000Mar 21 Frontal · CHRYSLER CORPORATION

    Certain of the driver's side air bag modules were assembled without an arming lever.

  • 95V056000Mar 21 Hood latch · CHRYSLER CORPORATION

    The secondary hood latch rod CAN bind on the guide bracket and prevent engagement of the secondary latch.

  • 95V048000Mar 20 Pedals and linkages · GENERAL MOTORS CORP.

    Improperly manufactured brake pedal arm causes the brake pedal arm to fracture during braking.

  • 95V053000Mar 15 Tie rod assembly · FORD MOTOR COMPANY

    The inner tie rod assemblies were improperly manufactured and CAN fracture causing shaking or shimmy AT low speeds.

  • 95V052000Mar 15 Hoses, lines/piping, and fittings · FORD MOTOR COMPANY

    In some of the vehicles, brake tubes were misrouted between the master cylinder and the hydraulic control unit and results in exceeding the allowable stopping…

  • 95V054000Mar 13 Accessory scissor/screw/bottle jack/lift · VOLKSWAGEN OF AMERICA,INC

    The jacks supplied with these vehicles were assembled with an improperly machined spindle, so that a sharp ridge on the edge of spindle's thread would have…

  • 95V050000Mar 10 Accessory scissor/screw/bottle jack/lift · VOLVO CARS OF NA, INC.

    Some of the jacks supplied with the vehicles do not have the necessary load capacity.

  • 95V043000Mar 3 Interior/under dash · HYUNDAI MOTOR AMERICA

    The engine control module wiring harness under the instrument panel CAN be contacted by the clutch pedal assembly when the clutch is engaged.

  • 95V028000Mar 1 Antilock/traction control/electronic limited slip · NISSAN NORTH AMERICA, INC.

    The anti-lock braking system (ABS) hydraulic actuator was not properly purged of all air during the fill and evacuation process causing air bubbles to get into…

February 1995

  • 95V037000Feb 28 Labels · FORD MOTOR COMPANY

    The certification label on these vehicles have incorrect rear tire sizes listed. P215/70r14sl should be p215/75r14sl. This does not comply with fmvss no. 120,…

  • 95V030000Feb 27 Steering wheel/handle bar · GENERAL MOTORS CORP.

    The four (4) steering column support bracket attaching bolts were under torqued during assembly.

  • 95V033000Feb 21 Engine · MAZDA (NORTH AMERICA),INC

    The wire rod used in the manufacture of the engine valve springs CAN develop minute cracks causing breakage of the springs.

  • 95V031000Feb 21 Wiring · MERCEDES-BENZ USA, INC.

    The front passenger metal foot rest CAN, over time, abrade through the wiring harness under the foot rest causing the wiring harness to short circuit.

  • 95V026000Feb 16 Cooling unit and lines · GENERAL MOTORS CORP.

    Due to a thin case casting, an external transmission leak CAN occur.

  • 95V025000Feb 16 Lower arm · GENERAL MOTORS CORP.

    These vehicles have been built with welds missing from the front suspension lower control arm assemblies causing excessive loads on the existing welds.

  • 94V025002Feb 14 Exterior · CHRYSLER CORPORATION

    The right outside rearview mirror contains convex glass rather than flat. Therefore, these vehicles fail to comply with fmvss no. 111, "rearview mirrors."

  • 95V023000Feb 13 Vehicle speed control · AM GENERAL CORPORATION

    Water CAN accumulate in the cruise control cable and if the outside temperature is below freezing and the cruise control is engaged, the water CAN freeze…

January 1995

  • 95V009000Jan 24 Windshield · FORD MOTOR COMPANY

    The glass tempering process on the right hand rear door windows was not correctly performed. This does not meet the requirements of fmvss no. 205, "glazing…

  • 95V008000Jan 24 Hoses, lines/piping, and fittings · NISSAN NORTH AMERICA, INC.

    Certain of the brake hoses for the right rear wheel were routed incorrectly so that contact is made with a suspension component. This causes abrasion to the…

  • 95V003000Jan 20 High/low beam dimmer switch · HYUNDAI MOTOR AMERICA

    A plastic slider piece within the headlamp dimmer switch assembly does not fully retract when the headlamp dimmer switch is moved from low beam to high beam…

  • 95V005000Jan 18 Buckle assembly · CHRYSLER CORPORATION

    The cinch bar component within the passenger side safety belt buckle assembly shatters causing the belt to release.