Chevrolet · C20

1994 Chevrolet C20 Recalls

Model year 1994

Recalls 8 NHTSA campaigns Complaints 12 Most: brakes
Fuel economy n/a No EPA rating
Crash rating pre-2011 NHTSA 5-Star program

There are 8 safety recalls on file for the 1994 Chevrolet C20, filed between September 1993 and February 1999. Each one is repaired free by a franchised Chevrolet dealer, no matter how old the car is or who owns it now.

A recall covers a range of build dates, so not every 1994 C20 is affected by every campaign below. To see which ones apply to your car and whether they were already done, enter its VIN at nhtsa.gov/recalls.

1999 (1)

99V025000 Filed Feb 5, 1999 988,587 vehicles

Switch

Vehicle description: pickup trucks, crew cabs, utility trucks and sport utility vehicles. These vehicles were built with the polarity of the wiring for the zero adjust brake switch reversed from what was specified on the switch drawing. With the reversed polarity, the contacts in the brake switch CAN wear out prematurely. The brake switch will perform normally until the brake switch contacts wear out, resulting in loss of the brake lamps without any warning to the driver.

Risk and remedy
Risk
This would fail to warn a following driver that the vehicle is braking and could lead to a crash.
Remedy
Dealers will replace the brake switch and reverse the wiring.
Filed by
GENERAL MOTORS CORP. (manufacturer number 98065)

1995 (3)

95V246000 Filed Dec 21, 1995 675,661 vehicles

Seats

The seat recliner to seat frame attaching bolts on these vehicle could loosen, fatigue and fracture, allowing the seat back to suddenly recline.

Risk and remedy
Risk
If this were to occur to the driver's seat, this could result in a sudden loss of vehicle control increasing the risk of a vehicle accident.
Remedy
Dealers will remove all foam and/or fabric sandwiched between the recliner assembly and the seat frame, install washers between the seat recliner and the seat frame AT each attachment point, and install new attaching bolts torqued to a higher specification. These corrections will be made to both the driver's and passenger's seats.
Filed by
GENERAL MOTORS CORP.
95V242000 Filed Dec 13, 1995 40 vehicles

Seat belts front

These vehicles were built with front seat belt systems with no energy management loops and may not meet the head injury criteria requirements of fmvss no. 208, "occupant crash protection."

Risk and remedy
Risk
In the event of a vehicle crash, the occupants of these seats may not be properly restrained.
Remedy
Dealers will replace the retractor portion of the seat belt assembly(s) with one having the newly designed energy-management twin-loop system.
Filed by
GENERAL MOTORS CORP.
95V241000 Filed Dec 13, 1995 630,099 vehicles

Seat belts front

If both the lap-belt and shoulder-belt energy management loops on the front seat belt assemblies release AT or near the same time, acceleration forces CAN cause the buckle release mechanism to activate and allow the buckle to separate from the latch.

Risk and remedy
Risk
If the buckle released, the system would fail to provide adequate occupant restraint protection.
Remedy
Dealers will remove the stitching that creates the energy management loop in the shoulder belt(s).
Filed by
GENERAL MOTORS CORP.

1994 (2)

94V212000 Filed Oct 26, 1994 29 vehicles

Windshield

The windshields were installed with incorrect windshield opening pinch-weld-flange primer. This primer will not properly etch the painted surface of the flange, allowing the windshield to separate from the vehicle during a collision. This does not comply with the requirements of fmvss no. 212, "windshield mounting."

Risk and remedy
Risk
Consequence of non-compliance: the separation of the windshield from the vehicle during collision increases the risk of injury for all persons involved.
Remedy
Dealers will remove the windshield and reinstall it using the correct primer.
Filed by
GENERAL MOTORS CORP.
94V060000 Filed Apr 5, 1994 30,148 vehicles

Lower arm

Trucks were assembled with the left-hand lower control arm to frame rear nut tightened below the specified torque. Low torque on this nut may allow the attachment bolt to loosed and subsequently fatigue and break. The bolt breakage CAN cause the left hand control arm to separate from the frame.

Risk and remedy
Risk
If this occurs, a loss of vehicle control and a crash could result.
Remedy
Dealers will tighten the left-hand lower control arm to frame rear nut to the proper torque specification.
Filed by
GENERAL MOTORS CORP.

1993 (2)

93V216000 Filed Dec 14, 1993 1,375 vehicles

Seats

The seats have been assembled without bolts that connect the upper slave hinge to the seat back frame, or without bolts that connect the seat to the seat adjuster. In either case, the vehicles fail to conform to fnvss no. 207, "seating systems."

Risk and remedy
Risk
The missing bolts may cause the driver's seat to becomeloose and in a sudden stop or accident may subject the occupant to increasedrisk of injury.
Remedy
Dealers will inspect seats for missing bolts and install bolts if required.
Filed by
GENERAL MOTORS CORP.
93V152000 Filed Sep 15, 1993 70,154 vehicles

Pedals and linkages

The brake pedal push rod retainer is missing, mispositioned or not properly seated.

Risk and remedy
Risk
Brake pedal push rod problems CAN cause the stop lampswitch and the brake booster push rod to disconnect from the brake pedal,resulting in loss of brake operation, and a vehicle crash could occur withoutprior warning.
Remedy
Inspect vehicles to assure the brake pedal push rod retainer is present and fully seated in its correct position.
Filed by
GENERAL MOTORS CORP.

Recall questions

How many recalls does the 1994 Chevrolet C20 have?

NHTSA lists 8 recalls for the 1994 Chevrolet C20.

How do I know if my car's recall was fixed?

Enter your 17-character VIN at nhtsa.gov/recalls or on the manufacturer's site. It shows any recall that has not been repaired on that specific vehicle.