Ford · Explorer

1991 Ford Explorer Recalls

Special purpose vehicle · 4WD/AWD, RWD · Regular

There are 8 safety recalls on file for the 1991 Ford Explorer, filed between May 1990 and December 1997. Each one is repaired free by a franchised Ford dealer, no matter how old the car is or who owns it now.

A recall covers a range of build dates, so not every 1991 Explorer is affected by every campaign below. To see which ones apply to your car and whether they were already done, enter its VIN at nhtsa.gov/recalls.

1997 (1)

97V235001 Filed Dec 18, 1997 185,000 vehicles

Roof and pillars

Vehicle description: multi-purpose passenger vehicles equipped with factory installed sunroof. The sunroof glass panel assembly CAN separate while the vehicle is moving due to incorrect hinge engagement. This was caused by improper sunroof installation of the glass panel.

Risk and remedy
Risk
Unexpected separation of the sunroof glass panel could possibly distract the driver increasing the risk of a vehicle crash or loss of vehicle control.
Remedy
Owners will be provided with an instruction booklet which thoroughly outlines, with illustrations, the proper procedures for the removal, storage, and reinstallation of the sunroof's glass panel. A warning label for attachment to the sunroof's latch knob will also be provided to the owners.
Filed by
FORD MOTOR COMPANY

1996 (1)

96V024001 Filed Feb 5, 1996 108,000 vehicles

Hydraulic

The studs which attach the brake master cylinder to the power brake vacuum booster assembly CAN develop stress corrosion cracking after being operated for an extended period of time in the southern california location.

Risk and remedy
Risk
If a crack occurs, it could result in one or both studs fracturing. The master cylinder could then separate from the vacuum booster, when the brakes are applied, preventing the service brakes from activating increasing the risk of a vehicle accident.
Remedy
Dealers will replace the power brake vacuum booster assembly.
Filed by
FORD MOTOR COMPANY

1992 (1)

92V113000 Filed Aug 17, 1992 565,000 vehicles

Buckle assembly

The rigid mounted safety belt buckles are defective in three ways. First, a fastened safety belt buckle will not unlatch when the release button is depressed. This results from interference between the buckle ejector finger and the buckle tongue window. The second defect is the safety belt buckle may not latch. The third possible defect is that the tongue may be retained by the buckle, but it may not be latched sufficiently to provide occupant protection.

Risk and remedy
Risk
An insufficiently latched or unlatched safety beltincreases the risk of injury to seat occupants in the event of a sudden stop oraccident. If the safety belt buckle will not unlatch, it will not allow theoccupant to get out of the vehicle in an emergency situation.
Remedy
Ford will replace the rigid mounted safety belt buckles with end release safety belt buckles designed to prevent latch problems.
Filed by
FORD MOTOR COMPANY

1991 (4)

91V189000 Filed Nov 4, 1991 792,000 vehicles

Automatic transmission

When the automatic transmission shift lever is placed in the park position, the park pawl does not always abut or engage the park gear.

Risk and remedy
Risk
Driver may believe the vehicle is safely engaged in parkwhen the gear is not truly engaged. This CAN lead to the vehicle jumping out ofgear unintentionally, vehicle rollaway when parked on a sloped surface, andinadvertent motion when the vehicle is started. All of these conditions canresult in a vehicle accident.
Remedy
Repair the transmission with a new park pawl.
Filed by
FORD MOTOR COMPANY
91V026000 Filed Feb 12, 1991 220,000 vehicles

Bumpers

Rear bumper reinforcement may be subject to fatigue cracking under extended trailer tow service when using a bumper-mounted trailer hitch ball.

Risk and remedy
Risk
Under extreme conditions, bumper could separate from thevehicle when using a bumper mounted trailer hitch ball.
Remedy
Install two brackets to reinforce the bumper.
Filed by
FORD MOTOR COMPANY
91V025000 Filed Feb 11, 1991 18,000 vehicles

Tank assembly

The hot plate weld which attaches the vapor vent valve carrier to the top of the plastic fuel tank may partially fracture, allowing vapor of fuel to escape from the top of the tank.

Risk and remedy
Risk
The escaped vapor or leaked fuel could cause a fire inthe presence of a source of ignition.
Remedy
Fuel tank will be removed and inspected for weld integrity. Fuel tanks with inadequate welds will be replaced.
Filed by
FORD MOTOR COMPANY
91V024000 Filed Feb 11, 1991 25,000 vehicles

Tank assembly

The front heat shield may contact the front of the plastic fuel tank, causing cuts or other damage to the extent of penetration.

Risk and remedy
Risk
This penetration of the fuel tank causes vapors to escapeand possibly fuel to spill, which could catch fire in the presence of anignition source.
Remedy
Relocate the heat shield; inspect and replace damaged fuel fuel tanks.
Filed by
FORD MOTOR COMPANY

1990 (1)

90V098000 Filed May 21, 1990 2,500 vehicles

Sun/moon roof assembly

If sunroof glass is removed and reinstalled by vehicle operator, hinge assemblies CAN be accidentally improperly mated.

Risk and remedy
Risk
Sunroof could detach from the vehicle while being driven,creating a risk to following vehicles or people in the vicinity, or to vehicleoccupants if the glass should fall into the cabin.
Remedy
Install revised sunroof hinges that will adequately retain sunroof assembly.
Filed by
FORD MOTOR COMPANY

Recall questions

How many recalls does the 1991 Ford Explorer have?

NHTSA lists 8 recalls for the 1991 Ford Explorer.

How do I know if my car's recall was fixed?

Enter your 17-character VIN at nhtsa.gov/recalls or on the manufacturer's site. It shows any recall that has not been repaired on that specific vehicle.