There are 5 safety recalls on file for the 1995 Ford Explorer,
filed between March 1995 and October 2009.
Each one is repaired free by a franchised Ford dealer, no matter how old the car is or who owns it now.
A recall covers a range of build dates, so not every 1995 Explorer is affected by every campaign below.
To see which ones apply to your car and whether they were already done, enter its VIN at nhtsa.gov/recalls.
2009 (1)
09V399000
Filed Oct 13, 2009 4,500,000 vehicles
Ford is recalling model years 1995-2003 windstar, 2000-2003 excursion diesel, 1993-1997 and 1999-2003 F-250 sd through f-550 sd diesel, 1992-2003 e-150 through e-550, 1995-2002 explorer, 1997 and 2002 mercury mountaineer, 1995-1997 and 2001-2003 ranger, and 1994 f53 vehicles equipped with the texas instruments speed control deactivation switch (scds). The scds may leak internally and then overheat, smoke, or burn.
Risk and remedy
- Risk
- A vehicle fire could occur with or without the engine running.
- Remedy
- Ford will notify owners that dealers will install a fused wiring harness in line with the scds. On 1999-2003 windstar vehicles with a leaking scds, dealers will also inspect the ABS control module connector and repair as necessary. Repairs will be completed free of charge. The safety recall began on october 27, 2009. Owners may contact ford AT 1-888-222-2751.
- Filed by
- FORD MOTOR COMPANY (manufacturer number 09S09)
2000 (1)
00V402000
Filed Nov 28, 2000 810,000 vehicles
Vehicle description: sport utility vehicles. Under certain conditions, a front sway bar link CAN fracture.
Risk and remedy
- Risk
- Vehicle handling could be affected, increasing the risk of a crash.
- Remedy
- Dealers will replace both the left and right front sway bar links.
- Filed by
- FORD MOTOR COMPANY (manufacturer number 00S47)
1999 (1)
Vehicle description: on certain sport utility vehicles, the hydraulic lift cylinder bracket welds could fracture.
Risk and remedy
- Risk
- With a broken bracket weld, there is a potential for the liftgate bracket to gradually bend inward allowing the lift cylinder ball stud to disengage, unexpectedly allowing the liftgate to fall from an open position.
- Remedy
- Dealers will install liftgate reinforcement brackets. Depending upon the condition of the liftgate sheet metal in the area of the bracket, dealers may also install a larger reinforcement.
- Filed by
- FORD MOTOR COMPANY (manufacturer number 99S34)
1995 (2)
The inner tie rod assemblies were improperly manufactured and CAN fracture causing shaking or shimmy AT low speeds.
Risk and remedy
- Risk
- This condition CAN cause the wheel on the side with the broken tie rod to tuck inward or outward and slide resulting in an increased potential for a vehicle accident.
- Remedy
- Dealers will inspect the inner tie rods and replace the suspect tie rods.
- Filed by
- FORD MOTOR COMPANY
In some of the vehicles, brake tubes were misrouted between the master cylinder and the hydraulic control unit and results in exceeding the allowable stopping distances as required by fmvss no. 105, "hydraulic brake systems." in addition, seals within the master cylinder could be abraded by this condition over time resulting in an internal leak and a further reduction in brake performance.
Risk and remedy
- Risk
- Consequence of non-compliance: stopping distances could be longer than intended resulting in increased potential for a vehicle accident.
- Remedy
- Dealers will reroute the brake tubes.
- Filed by
- FORD MOTOR COMPANY
Recall questions
How many recalls does the 1995 Ford Explorer have?
NHTSA lists 5 recalls for the 1995 Ford Explorer.
How do I know if my car's recall was fixed?
Enter your 17-character VIN at nhtsa.gov/recalls or on the manufacturer's site. It shows any recall that has not been repaired on that specific vehicle.