There are 9 safety recalls on file for the 1992 Plymouth Voyager,
filed between October 1991 and July 1999.
Each one is repaired free by a franchised Plymouth dealer, no matter how old the car is or who owns it now.
A recall covers a range of build dates, so not every 1992 Voyager is affected by every campaign below.
To see which ones apply to your car and whether they were already done, enter its VIN at nhtsa.gov/recalls.
1999 (1)
99V189000
Filed Jul 16, 1999 828,559 vehicles
Vehicle description: minivans. The left hand windshield wiper pivot drive arm was not mechanically staked to the pivot shaft.
Risk and remedy
- Risk
- This could allow the drive arm to disengage from the shaft leading to a loss of wiper function. The driver's visibility would be impaired, increasing the risk of a crash.
- Remedy
- Dealers will replace the left hand side windshield wiper pivot assembly.
- Filed by
- DAIMLERCHRYSLER CORPORATION (manufacturer number 836)
1997 (3)
97V149000
Filed Sep 9, 1997 1,100,000 vehicles
Vehicle description: passenger mini-vans. The center rear seat, right outboard side, safety belt anchor hook CAN become unattached from the body anchor position.
Risk and remedy
- Risk
- In the event of a vehicle crash, the occupant may not be properly restrained increasing the risk of personal injury.
- Remedy
- Dealers will replace the anchor hook retaining clip with a revised profile clip and a cover plate.
- Filed by
- CHRYSLER CORPORATION
97V148000
Filed Sep 9, 1997 1,100,000 vehicles
Vehicle description: passenger mini-vans. Covers on the solid stalk mounted seat belt buckles CAN become dislodged causing the release button to stick inside the cover. The buckle would then be only partially latched.
Risk and remedy
- Risk
- In the event of a vehicle crash, the occupant may not be properly restrained increasing the risk of personal injury.
- Remedy
- Dealers will install a cover retaining clip to the stalk mounted buckle cover to prevent dislocation of the buckle cover.
- Filed by
- CHRYSLER CORPORATION
97V079000
Filed May 16, 1997 436,000 vehicles
The bolts used to attach the strut to the body and the rear liftgate CAN accumulate fatigue damage if three factors combine. If the bolt is loose, the gas strut is over-pressurized, and the frequency of opening and closing cycles is higher than for the average customer, the bolt CAN fail.
Risk and remedy
- Risk
- Personal injury could occur if the bolts break allowing the liftgate to fall suddenly.
- Remedy
- Dealers will inspect for loose fasteners, if the fasteners are loose, the strut (and integral bolts) will be replaced. If the bolt shows evidence of torque, the bolt will be removed, larger washers will replace the existing washer and the bolt will be reinstalled and hand tightened to the target torqued.
- Filed by
- CHRYSLER CORPORATION
1996 (2)
96V229000
Filed Nov 18, 1996 675,000 vehicles
The steering wheel armature stamping CAN crack and separate from the center hub attachment to the steering column.
Risk and remedy
- Risk
- If the steering wheel separates from the center hub attachment to the steering column, loss of control CAN occur increasing the risk of an accident.
- Remedy
- Dealers will inspect the steering wheel for armature cracks in the center hub attachment area. Any steering wheels showing cracks will be replaced. All other vehicles will have a reinforcement plate installed to prevent steering wheel separation in the event cracking occurs.
- Filed by
- CHRYSLER CORPORATION
96V099000
Filed Jun 13, 1996 321,000 vehicles
The ABS hydraulic control unit CAN experience excessive brake actuator piston seal wear causing pump-motor deterioration.
Risk and remedy
- Risk
- If this condition occurs, the ABS function could be lost and reduced power assist would be experienced during vehicle braking increasing the potential for a vehicle accident.
- Remedy
- Dealers will test the vehicle's anti-lock brake system and repair the vehicles if necessary. Also the warranty on all ABS components will be extended to 10 years or 100,000 miles (except for the brake actuator piston assembly and the pump-motor assembly which will have a lifetime coverage). Owners will also be reimbursed for previous ABS component repair costs.
- Filed by
- CHRYSLER CORPORATION (manufacturer number 685)
1992 (2)
Fuel tank flanges were not bent as required to allow the specified clearance for the fuel tank mounting straps and fuel lines AT the tank.
Risk and remedy
- Risk
- The unbent flanges to the fuel tank will damage themounting straps and/or fuel lines. The damaged mounting straps may break causingthe tank to drop and the damaged fuel line will leak fuel. In either case a firecould result if the spilled fuel is exposed to an ignition source.
- Remedy
- Repair the flange by bending to the correct angle; replace damaged fuel lines and mounting straps.
- Filed by
- CHRYSLER CORPORATION
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
Risk and remedy
- Risk
- Fractures of the upper steering column shaft couplingbolt result in a lack of coupling load on the shaft and loss of steeringcontrol.
- Remedy
- Replace the zinc plated bolt with a phosphate plated bolt.
- Filed by
- CHRYSLER CORPORATION
1991 (1)
The brake pedal pad attachment to the pedal arm may not have adequate strength due to mislocation of welds, and could break.
Risk and remedy
- Risk
- Failure of the pedal pad to pedal arm attachment resultsin loss of braking ability, and could result in an accident.
- Remedy
- Replace inadequate brake pedals with properly manufactured pedals.
- Filed by
- CHRYSLER CORPORATION
Recall questions
How many recalls does the 1992 Plymouth Voyager have?
NHTSA lists 9 recalls for the 1992 Plymouth Voyager.
How do I know if my car's recall was fixed?
Enter your 17-character VIN at nhtsa.gov/recalls or on the manufacturer's site. It shows any recall that has not been repaired on that specific vehicle.