There are 8 safety recalls on file for the 1994 Saab 900,
filed between April 1994 and February 1998.
Each one is repaired free by a franchised Saab dealer, no matter how old the car is or who owns it now.
A recall covers a range of build dates, so not every 1994 900 is affected by every campaign below.
To see which ones apply to your car and whether they were already done, enter its VIN at nhtsa.gov/recalls.
1998 (1)
Vehicle description: passenger vehicles. The instructions for properly aiming the headlighting system were omitted. This does not meet the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment."
Risk and remedy
- Risk
- If the headlamp assemblies are replaced, customers may not be able to properly aim the headlights.
- Remedy
- Owners will be sent aiming instructions, and directions for affixing these inserts to the owner guides. If an owner so desires, a dealer CAN affix the inserts in their owner guide for them.
- Filed by
- SAAB CARS USA, INC.
1997 (1)
Corrosion around the zinc-coated throttle control lever bushing CAN cause the throttle lever to bind.
Risk and remedy
- Risk
- This binding CAN result in the throttle plate not returning to the closed position when the throttle pedal is released and a subsequent loss of throttle control.
- Remedy
- Dealers will replace the zinc-coated throttle control lever bushing with a nickel-coated bushing and bolt.
- Filed by
- SAAB CARS USA, INC.
1995 (1)
It is possible to move the shift lever into the reverse gear position, remove the ignition key, and still have the transmission in neutral, or, to accidently disengage reverse by striking the gear lever.
Risk and remedy
- Risk
- If the parking brake is not applied, the car CAN roll from its original parked position increasing the potential for a vehicle accident.
- Remedy
- Dealers will replace transmission linkage components and complete a specially developed service adjustment procedure that will ensure that when the shift is moved to the reverse position, the reverse gear is actually engaged.
- Filed by
- SAAB CARS USA, INC.
1994 (5)
One or more of the arc welds CAN be missing on the seat back frame recliner.
Risk and remedy
- Risk
- This CAN result in a seat back falling backwards under a load.
- Remedy
- Both front seat backs will be inspected with the use of a hook to pull back the seat back upholstery. For any seat with missing welds, the seat back frame/recliner will be replaced.
- Filed by
- SAAB CARS USA, INC.
The two weld points in the rearward attachment bracket for the side impact protection beam in the rear door may be out of position. If the welds are out of position, the vehicles will not meet the requirements of fmvss 214, s5, "side door strength."
Risk and remedy
- Risk
- Consequence of non-compliance: passengers sitting in the rear seats will be subject to an increased risk of injury in the event of a side collision.
- Remedy
- Dealers will install support brackets AT the support weld locations.
- Filed by
- SAAB CARS USA, INC.
Two trigger springs mounted to the fore/aft adjustment lever do not develop sufficient force to properly lock the seat rails. After the seat is adjusted, this does not allow the seat rail lock to properly engage, which CAN cause the seat to move in a sudden stop or collision.
Risk and remedy
- Risk
- This CAN increase the possibility of injury to a seat occupant in the event of a sudden stop or accident.
- Remedy
- Dealers will remove both front seats and the two springs on each seat will be replaced with new springs with proper tension to ensure proper engagement.
- Filed by
- SAAB CARS USA, INC.
A weld in the seat rails was not made, increasing the risk of fatigue cracks forming around the attachment bushings on the height adjustment mechanism, causing the possibility of the height adjuster breaking in a rear end collision and allowing the seat to fold backwards.
Risk and remedy
- Risk
- This CAN increase the risk of injury to seat occupants.
- Remedy
- Dealers will install new front seat frame rails.
- Filed by
- SAAB CARS USA, INC.
The original front brake discs and/or pads shields do not protect the assemblies from being coated with a layer of slush, road salt or water while driving in snow or heavy rain. This CAN result in a delay in braking action that increases normal stopping distance.
Risk and remedy
- Risk
- Increased stopping distance could result in an accident.
- Remedy
- Dealers will replace the original front brake shields with a new design. An additional hole will be drilled in the steering king pin housing to attach a larger cover plate. A smaller protection plate will also be attached to the existing two bolts in the hub.
- Filed by
- SAAB CARS USA, INC.
Recall questions
How many recalls does the 1994 Saab 900 have?
NHTSA lists 8 recalls for the 1994 Saab 900.
How do I know if my car's recall was fixed?
Enter your 17-character VIN at nhtsa.gov/recalls or on the manufacturer's site. It shows any recall that has not been repaired on that specific vehicle.