Owners of the 2000 Chevrolet S-10 have reported 105 brakes problems to NHTSA, 22% of all complaints about this model year.
Where owners named a specific part, the most common were antilock/traction control/electronic limited slip (77), foundation components (13), and antilock (3).
The typical report came at around 65,000 miles, and complaints were filed between March 2000 and May 2024.
These brakes complaints include 20 crashes and 9 injuries.
For comparison, the 1994 S-10 has the most brakes complaints of any year, with 533.
Service and parking brakes: pedal feel, ABS and traction modules, rotors, calipers, hoses, master cylinders and brake boosters.
2 recalls for this model year involve the brakes.
If your problem matches, a dealer repairs it free under the recall.
Owners choose these labels when they file, so they are a guide rather than a diagnosis.
What owners say
BrakesFiled May 2024OK
My dad purchased my truck from the church secretary where he attended in March of 2015. At the time of purchase it only had 66,000 miles on it. The secretaryâs father owned it and used it from new until 6 months before we purchased it and only used it to help feed his cows. 1. Window washer motor circuit 2. Seatbelt needâs stitched 3.
Owner complaint 11589037 filed with NHTSA
BrakesFiled Oct 2019230,000 milesMOCrash
Tl* the contact owns a 2000 Chevrolet s10. While driving 26 MPH around an s curve, the brakes pedal was applied, but seized. The contact lost control of the vehicle and crashed into an embankment and creek. The air bags did not deploy. The driver was not wearing a seat belt and sustained neck, nose, and eye injuries that required medical attention. A police report was filed. The vehicle was towed to the contact's residence. The manufacturer and dealer were not contacted. The cause of the failures was not determined. The failure mileage was 230,000.
Owner complaint 11271790 filed with NHTSA
BrakesFiled Mar 2017131,000 milesTX
Tl* the contact owns a 2000 Chevrolet s10. While driving various speeds, the brake warning indicator illuminated. Also, the vehicle failed to stop when the brake pedal was depressed to the floorboard. The failure recurred. The vehicle was taken to an independent mechanic where it was diagnosed that there was oil leaking between the brake hose and front passenger wheel. The technician replaced the washer for the brake hose, but the failure recurred. The VIN was not included in NHTSA campaign number: 99v220000 (service brakes, hydraulic). The manufacturer was not made aware of the failure. The approximate failure mileage was 131,000.
Vehicle description: light duty pickup trucks equipped with 4-wheel disc brakes. Some of these vehicles have an antilock brake system (ABS) motor containing an out-of-specification spring clip. This clip could allow the motor bearing to become misaligned. If misalignment occurs, eventually the ABS would be non-functional.
Risk and remedy
Risk
The base brakes would remain fully functional, but the dynamic rear proportioning (drp) system, which optimizes front to rear brake balance, would become inoperative.
Remedy
Dealers will replace the brake pressure module valve assembly.
Vehicle description: s -trucks equipped with 2 wheel drive. These vehicles may have had the right-hand antilock brake system (ABS) module feed pipe and/or brake crossover pipe tube nuts tightened without seating the pipe-flared-ends enough to withstand normal assembly and vehicle inputs without partially unseating. This does not comply with requirements of fmvss no. 105, "hydraulic service brake normal, emergency, and park braking performance."
Risk and remedy
Risk
If this occurred, the seating seal could be broken during vehicle assembly, or from early road inputs or brake fluid cycling, and a leak could occur increasing the brake stopping distance.
Remedy
Dealers will inspect the brake pipe union for signs of brake fluid, and if necessary, install a new brake pipe union.