There are 6 safety recalls on file for the 1997 Chrysler Sebring,
filed between August 1997 and January 2004.
Each one is repaired free by a franchised Chrysler dealer, no matter how old the car is or who owns it now.
A recall covers a range of build dates, so not every 1997 Sebring is affected by every campaign below.
To see which ones apply to your car and whether they were already done, enter its VIN at nhtsa.gov/recalls.
2004 (1)
04V021000
Filed Jan 13, 2004 2,315,768 vehicles
On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
Risk and remedy
- Risk
- Either circumstance may result in the vehicle rolling away without warning.
- Remedy
- Dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler AT 1-800-853-1403.
- Filed by
- DAIMLERCHRYSLER CORPORATION (manufacturer number C45)
2002 (1)
On certain passenger vehicles equipped with 2.5l v6 engines, the throttle control cable CAN fray causing the throttle to bind or stick.
Risk and remedy
- Risk
- This could potentially result in a loss of throttle control, increasing the risk of a crash.
- Remedy
- Dealers will replace the throttle cable assembly. Owner notification began august 5, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler AT 1-800-853-1403.
- Filed by
- DAIMLERCHRYSLER CORPORATION (manufacturer number B22)
2000 (1)
00V421002
Filed Dec 18, 2000 393,796 vehicles
Vehicle description: passenger vehicles. If the rubber boots on the lower lateral arm ball joints of the front suspension were damaged during assembly, dirt and water CAN intrude. Also, mmc has added the potential of leaking moisture, which CAN cause the ball stud to corrode.
Risk and remedy
- Risk
- This condition could cause the lower lateral arm ball joint to separate, increasing the risk of a vehicle crash. This campaign supercedes mmc's previous safety recall campaign, see 99v-066.
- Remedy
- Dealers will inspect the lower lateral arm ball joint for wear. Ball joints that exhibit wear beyond the established tolerance will be replaced with newly designed lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent intrusion of moisture.
- Filed by
- DAIMLERCHRYSLER CORPORATION (manufacturer number 967)
1998 (1)
Vehicle description: passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key CAN cause a trapped key condition which CAN result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, CAN break the connecting pin in the shifter.
Risk and remedy
- Risk
- If this happens, the "ignition-park" interlock system will be nonfunctional.
- Remedy
- Dealers will inspect for proper operation of the system. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a "self-adjusting" design.
- Filed by
- CHRYSLER CORPORATION
1997 (2)
97V201000
Filed Nov 13, 1997 599,000 vehicles
Vehicle description: passenger vehicles. The lower control arm ball joint CAN separate due to loss of lubrication.
Risk and remedy
- Risk
- Separation of the ball joint could cause a loss of steering control increasing the risk of a vehicle crash.
- Remedy
- Dealers will inspect the ball joint end housing cover seal for leakage with a high pressure air tester and the rubber boot will be visually inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.
- Filed by
- CHRYSLER CORPORATION
The headrest guide bracket was improperly welded to the seat back frame on the passenger side seat back assemblies only.
Risk and remedy
- Risk
- The headrest support bracket CAN break, increasing the risk of personal injury.
- Remedy
- Dealers will replace the passenger seat back assembly with a new assembly.
- Filed by
- CHRYSLER CORPORATION
Recall questions
How many recalls does the 1997 Chrysler Sebring have?
NHTSA lists 6 recalls for the 1997 Chrysler Sebring.
How do I know if my car's recall was fixed?
Enter your 17-character VIN at nhtsa.gov/recalls or on the manufacturer's site. It shows any recall that has not been repaired on that specific vehicle.