Owners of the 1996 Chrysler Sebring have reported 85 suspension problems to NHTSA, 20% of all complaints about this model year.
Where owners named a specific part, the most common were front (84) and rear (6).
The typical report came at around 99,000 miles, and complaints were filed between October 1996 and November 2018.
These suspension complaints include 10 crashes, 1 fire, and 3 injuries.
No other Sebring year has as many suspension complaints.
Springs, struts, shocks, control arms, ball joints, bushings and stabilizer links, front and rear.
3 recalls for this model year involve the suspension.
If your problem matches, a dealer repairs it free under the recall.
Complaints85
Typical mileage99k
Crashes / fires10 / 1
Injuries3
Parts named in these complaints
Front84
Rear6
Owners choose these labels when they file, so they are a guide rather than a diagnosis.
What owners say
SuspensionFiled Nov 2010UT
1996 Chrysler Sebring coupe. Consumer writes regarding Chrysler employee lunch break activities *tgw the consumer stated he experienced mechanical failure while driving 20 MPH. The left front ball joint suddenly separated and jammed the tire up into the fender well AT an awkward angle. The consumer stated it cost over $800 to replace the suspension parts on both sides. The consumer stated the reason for the failure, was due to lack of lubrication, because years ago, manufacturers chose to delete the inexpensive grease fitting on suspension parts and instead chose substituted sealed ball joints that were subject to failure.
Owner complaint 10366054 filed with NHTSA
SuspensionFiled Dec 2009IL
Recall #750 front lower control arm ball joint alleged repaired 02-10-98. This is a new (10-08-09) recall. Due to my vehicle was AT the dealer, it was asked if the numbers of the ball joints and control arms numbers could be checked to see if original Chrysler or aftermarket quality parts were used. Though this is a serious safety issue, loss of steering, the service advisor advised I'd need to check the original repair order (02-10-98). The original owner is deceased.
Owner complaint 10294207 filed with NHTSA
SuspensionFiled Jan 200790,000 milesWI
Lower lateral arm broke on our 1996 Chrysler Sebring. Dealer and Chrysler have refused to fix the car under recall. This is the 3rd major failure and inconvenience of this part. The last failure was 8 moths ago. There is clearly a safety issue here as well as a mechanical defect.
Vehicle description: passenger vehicles. If the rubber boots on the lower lateral arm ball joints of the front suspension were damaged during assembly, dirt and water CAN intrude. Also, mmc has added the potential of leaking moisture, which CAN cause the ball stud to corrode.
Risk and remedy
Risk
This condition could cause the lower lateral arm ball joint to separate, increasing the risk of a vehicle crash. This campaign supercedes mmc's previous safety recall campaign, see 99v-066.
Remedy
Dealers will inspect the lower lateral arm ball joint for wear. Ball joints that exhibit wear beyond the established tolerance will be replaced with newly designed lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent intrusion of moisture.
Filed by
DAIMLERCHRYSLER CORPORATION (manufacturer number 967)
Vehicle description: passenger vehicles. If the rubber boots on the lower lateral arm ball joints of the front suspension were damaged during assembly, dirt and water CAN intrude.
Risk and remedy
Risk
This condition could cause the lower lateral arm ball joint to separate, increasing the risk of a vehicle crash.
Remedy
Dealers will inspect the rubber boots, and if the boot is damaged, they will replace the lower lateral arm and ball joint on the affected vehicles.
Filed by
DAIMLERCHRYSLER CORPORATION (manufacturer number 827)
Vehicle description: passenger vehicles. The lower control arm ball joint CAN separate due to loss of lubrication.
Risk and remedy
Risk
Separation of the ball joint could cause a loss of steering control increasing the risk of a vehicle crash.
Remedy
Dealers will inspect the ball joint end housing cover seal for leakage with a high pressure air tester and the rubber boot will be visually inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.