There are 8 safety recalls on file for the 1994 Ford F-250,
filed between September 1993 and August 2006.
Each one is repaired free by a franchised Ford dealer, no matter how old the car is or who owns it now.
A recall covers a range of build dates, so not every 1994 F-250 is affected by every campaign below.
To see which ones apply to your car and whether they were already done, enter its VIN at nhtsa.gov/recalls.
2006 (1)
06V286000
Filed Aug 1, 2006 1,200,000 vehicles
On certain trucks equipped with speed control, gasoline or natural gas engines, the speed control deactivation switch may overheat.
Risk and remedy
- Risk
- Overheating could result in smoke or burn and an underhood fire.
- Remedy
- Dealers will install a fused wiring harness into the speed control system free of charge. The recall began on august 7, 2006. Owners may contact ford AT 1-866-436-7332. (note: also see recalls 05v017 and 05v388)
- Filed by
- FORD MOTOR COMPANY (manufacturer number 05S28)
2005 (1)
05V388000
Filed Sep 7, 2005 4,500,000 vehicles
On certain pickup trucks and sport utility vehicles equipped with speed control, the speed control deactivation switch may overheat, smoke, or burn.
Risk and remedy
- Risk
- A fire AT the switch could occur.
- Remedy
- By letter dated september 12, 2005, owners were instructed to return their vehicles to their dealers to have the speed control deactivation switch disconnected. Owners who have had their speed control deactivated are being notified that parts will be available and advised to make an appointment to reconnect the speed control beginning in february 2006. Owners who did not have their speed control deactivated are being notified to have their system remedied beginning in february 2006. Owners are urged to avail themselves of the free disconnect service as soon as possible because of the significant risk of fire. Owners may contact ford AT 1-800-392-3673. (note: also see recalls 05v017 and 06v286)
- Filed by
- FORD MOTOR COMPANY (manufacturer number 05S28)
1996 (1)
The wire harness for the power lumbar feature on the seat is underneath the front seat cushion support wires. The support wires on the driver seat CAN contact and damage the insulation harness resulting in a high resistance electrical short through the support wires.
Risk and remedy
- Risk
- Consequence of defect: over heating of the support wires could result, and melting, smoke, or possible igntion of the surrounding materials could occur.
- Remedy
- Dealers will inspect the seats on the affected vehicles. If no damage is found, the driver seat wire harness will be covered with a protective convolute tubing, wrapped with electrical tape and the harness will be rerouted. If damage is found, the wire harness will be replaced.
- Filed by
- FORD MOTOR COMPANY
1994 (3)
The parking brake control self-adjust pawl does not line up properly with the self-adjust rachet causing the pawl to slip over one or more teeth in the rachet.
Risk and remedy
- Risk
- When the above occurs, it CAN result in parking brake system ineffectiveness. The parking brake will not hold the vehicle, causing the vehicle to roll freely, if the transmission is not left in gear.
- Remedy
- A wedge will be installed which will serve to lock the parking brake self-adjust mechanism pawl into engagement with the rachet. Also, owners will be advised to release and reapply the parking brake whenever tooth skip occurs and will be reminded to always turn off the engine and leave the vehicle in gear when the vehicle is parked.
- Filed by
- FORD MOTOR COMPANY
In a heavily loaded vehicle, while in the cruise control mode, the throttle may not reduce immediately when the load on the engine is decreased (such as when the vehicle crests a hill.) this CAN result in increased vehicle speed without prior warning.
Risk and remedy
- Risk
- This CAN result in loss of speed control of the vehicle, and a possible accident.
- Remedy
- Dealers will replace the electronic engine control module.
- Filed by
- FORD MOTOR COMPANY
The u-clip style nuts that retain the front bumpers to the front bumper inner arms CAN fracture.
Risk and remedy
- Risk
- If one of the u-clip nuts fractures, the bumper will loosen and rattle causing fracture of the remaining u-clip nuts, resulting in separation of the bumper from the vehicle. If the bumper were to detach from the vehicle while it is being driven, a vehicle collision could result.
- Remedy
- Inspection and replacement of the four u-clip nuts and the associated bolts.
- Filed by
- FORD MOTOR COMPANY
1993 (2)
These vehicles were built with nonfunctional air bag diagnostic modules intended for certain vehicles over 8,500 bls. Gvwr.
Risk and remedy
- Risk
- The air bag supplemental restraint and the air bagwarning light will not function. This could result in reduced occupantprotection in the event of a collision that should activate the air bagsupplemental restraint system.
- Remedy
- Dealers will inspect these vehicles and, if necessary, install the correct air bag diagnostic module.
- Filed by
- FORD MOTOR COMPANY
The design of the air bag diagnostic monitor causes the driver's side air bag to deploy when the passenger door is slammed while the ignition key is turned to the start position.
Risk and remedy
- Risk
- Inadvertent deployment of the air bag CAN result ininjury to the driver.
- Remedy
- Install a redesigned air bag diagnostic monitor.
- Filed by
- FORD MOTOR COMPANY
Recall questions
How many recalls does the 1994 Ford F-250 have?
NHTSA lists 8 recalls for the 1994 Ford F-250.
How do I know if my car's recall was fixed?
Enter your 17-character VIN at nhtsa.gov/recalls or on the manufacturer's site. It shows any recall that has not been repaired on that specific vehicle.