Owners of the 2000 GMC Yukon have reported 59 brakes problems to NHTSA, 36% of all complaints about this model year.
Where owners named a specific part, the most common were antilock/traction control/electronic limited slip (24), foundation components (6), and conventional (4).
The typical report came at around 83,000 miles, and complaints were filed between June 2000 and November 2014.
These brakes complaints include 9 crashes and 2 injuries.
For comparison, the 1999 Yukon has the most brakes complaints of any year, with 113.
Service and parking brakes: pedal feel, ABS and traction modules, rotors, calipers, hoses, master cylinders and brake boosters.
2 recalls for this model year involve the brakes.
If your problem matches, a dealer repairs it free under the recall.
Owners choose these labels when they file, so they are a guide rather than a diagnosis.
What owners say
BrakesFiled Nov 2014149,000 milesNV
Tl* the contact owns a 2000 GMC Yukon. The contact experienced failures related to NHTSA campaign number: 05v379000 (service brakes, hydraulic). The contact stated that while driving 5-10 MPH while inititating a turn, the brakes failed to respond. The vehicle was not taken to a dealer. The manufacturer was made aware of the failure. The failure mileage was 149,000.
Owner complaint 10652511 filed with NHTSA
BrakesFiled Jul 2014155,000 milesMNCrash
Coming to a stop and brake pedal went to floor....my vehicle then rolled into intersection causing an accident when the other vehicle collided with the front of my vehicle. Further investigation found brake line burst. To remedy situation I replaced all brake lines.
Owner complaint 10609672 filed with NHTSA
BrakesFiled Jun 2014179,000 milesVA
Brought Yukon in to koons GMC in manassas, virginia in 2012 for two recalls which I was told were both done along with getting an estimate for $3300 for largely an intake manifold. I have called GM corp and been told many times over that past two years as more cars have been added to recall lists that there were no remaining recalls for my vehicle; now GM corporate says the wheel sensor recall (necessary to avoid low speed crashes) was actually never performed and GM corporate cannot explain why I have been told by both dealerships in the DC area and GM corporate over the past two years (exceeding 10 total calls) since that there were no…
Certain pickup trucks and sport utility vehicles may experience unwanted antilock brake system (ABS) activation. This condition is more likely to occur in environmentally corrosive areas. This recall will be launched in the "salt belt" states of connecticut, delaware, illinois, indiana, iowa, maryland, massachusetts, maine, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin and the district of columbia only.
Risk and remedy
Risk
This CAN cause increased stopping distances during low-speed brake applications, which could result in a crash.
Remedy
Dealers are to remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply rust inhibitor to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the peak-to-peak output voltage to ensure the wheel speed signal is within specifications. The recall began september 22, 2005. Owners may contact chevrolet AT 1-800-630-2438 or GMC AT 1-866-996-9463.
Vehicle description: light duty pickup trucks and sport utility vehicles. Some of these vehicles have a clearance condition between the front right-hand brake pipe and the body cross sill that could decrease to the point of allowing contact during the life of the vehicle. If contact occurs and the brake pipe becomes damaged, in half of the brake system there CAN be a loss of brake fluid and pressure. The brake warning lamp will be activated when the brake fluid level reaches the indicator limit.
Risk and remedy
Risk
During braking, the pedal will be lower than normal and stopping distances will be longer. If this occurs when stopping distance is limited, a crash could occur.
Remedy
Dealers will inspect the front right-hand brake pipe for wear. If there are signs of wear, this section of the brake pipe will be replaced with a new designed brake pipe section. If there are not signs of wear on the brake pipe, the dealer will install a spacer clip to ensure sufficient clearance between the brake pipe and the body cross sill.