Ford · Crown Victoria

1991 Ford Crown Victoria

Model year 1991

Recalls 3 NHTSA campaigns Complaints 55 Most: air bags
Fuel economy n/a No EPA rating
Crash rating pre-2011 NHTSA 5-Star program

Owners have filed 55 complaints about the 1991 Ford Crown Victoria with NHTSA, the 14th highest of 22 Crown Victoria years.

The largest share concerns the air bags (11 complaints, 20% of the total), followed by electrical system (10) and engine (7).

Complaints for this year mention 8 crashes, 5 fires, and 6 injuries. These are owner reports and have not been verified by NHTSA.

NHTSA lists 3 recalls for this model year. The most recent, campaign 98V322000, was filed in December 1998 and concerns the lower ball joint.

What owners report

Full breakdown
98V322000 Filed Dec 16, 1998 175,000 vehicles

Lower ball joint

Vehicle description: certain 1996-1999 ford crown victoria police, fleet, natural gas, and 1996-1999 lincoln town car limousine vehicles that were produced with a lower control arm ball joint containing a one piece bearing; and 1990-1996 ford crown victoria police, fleet, and ngv vehicles and 1990-1996 lincoln town car limousine vehicles that have been serviced with either a ball joint containing the one-piece bearing or a front lower control arm containing a ball joint with a one-piece bearing. The one-piece bearing within the lower control arm ball joint CAN weaken slowly during use and eventually crack. This could result in separation of the ball and cap of the joint, allowing the control arm to drop to the ground.

Risk and remedy
Risk
If this occurs while the vehicle is moving, reduced steering control could occur, increasing the risk of a crash.
Remedy
Dealers will replace the lower control arm ball joints (2).
Filed by
FORD MOTOR COMPANY (manufacturer number 98S37)
92V075000 Filed May 19, 1992 25,000 vehicles

Hoses, lines/piping, and fittings

The rear brake lines have inadequate clearance between the brake tube and the vehicle underbody in the area of the left rear wheel opening.

Risk and remedy
Risk
Inadequate clearance CAN cause abrasion of the brake lineand a leak CAN develop, resulting in loss of brake fluid to the rear brakesystem and increased stopping distances.
Remedy
Repair any brake lines that have an indication of contact or have the potential for contact with the body of the vehicle. Relocate lines, if necessary.
Filed by
FORD MOTOR COMPANY
91V048000 Filed Mar 18, 1991 6,800 vehicles

Automatic transmission

The park rod assembly contains a park cam with inadequate surface hardness, which could lead to park disengagement or no park engagement when the lever is placed in park.

Risk and remedy
Risk
If park is not engaged and the parking brake is off, avehicle roll-away could result.
Remedy
Replace park rod assembly on automatic transmissions.
Filed by
FORD MOTOR COMPANY

Recent owner reports

Complaints as owners filed them with NHTSA, lightly tidied for readability. They are not verified.

Speed control Filed Oct 2006 100,000 miles IL

Dt*: the contact stated while AT a stop, the gearshift was shifted into drive and the vehicle accelerated out of control, bounced over a high curb, and was fishtailing. The contact estimated the speed to have reached 70 MPH before the ignition was turned off. The vehicle was towed to the service dealer, who determined that the throttle pedal had seized. The manufacturer was notified. Updated 12/5/2006 -

Owner complaint 10171453 filed with NHTSA
Engine Filed Dec 2003 89,000 miles AL

When the vehicle was idling the consumer smelled a heavy scent of oil burning. While driving AT 65 MPH, the engine began revving AT a high rate. Also, the transmission gears would not go into third or fourth gear. The vehicle was taken to the dealer, who informed the consumer that the bushing was made of plastic. However, the bushing should be made from metal. The manufacturer had been informed. *ak when the cable linkage was disconnected, the destruction of the clutch would occur. (locking up the higher two gears, without the lock up only the first and second gear would work)

Owner complaint 10046325 filed with NHTSA
Transmission and drivetrain Filed Dec 2003 89,000 miles AL

When the vehicle was idling the consumer smelled a heavy scent of oil burning. While driving AT 65 MPH, the engine began revving AT a high rate. Also, the transmission gears would not go into third or fourth gear. The vehicle was taken to the dealer, who informed the consumer that the bushing was made of plastic. However, the bushing should be made from metal. The manufacturer had been informed. *ak when the cable linkage was disconnected, the destruction of the clutch would occur. (locking up the higher two gears, without the lock up only the first and second gear would work)

Owner complaint 10046325 filed with NHTSA

How 1991 compares with other Crown Victoria years

Owner complaints per model year. The highlighted column is this year.

Questions about the 1991 Ford Crown Victoria

Does the 1991 Ford Crown Victoria have any recalls?

Yes. NHTSA lists 3 recalls for the 1991 Ford Crown Victoria, most recently 98V322000 (December 1998) for the lower ball joint.

What are the most common problems with the 1991 Ford Crown Victoria?

Owner complaints to NHTSA most often involve the air bags (11), electrical system (10), and engine (7).