Owners of the 1994 Ford Crown Victoria have reported 26 suspension problems to NHTSA, 14% of all complaints about this model year.
Where owners named a specific part, the most common were front (25).
The typical report came at around 134,000 miles, and complaints were filed between March 1995 and April 2020.
For comparison, the 1996 Crown Victoria has the most suspension complaints of any year, with 51.
Springs, struts, shocks, control arms, ball joints, bushings and stabilizer links, front and rear.
2 recalls for this model year involve the suspension.
If your problem matches, a dealer repairs it free under the recall.
Complaints26
Typical mileage134k
Crashes / fires0 / 0
Injuries0
Parts named in these complaints
Front25
Owners choose these labels when they file, so they are a guide rather than a diagnosis.
What owners say
SuspensionFiled Apr 2020140,000 milesPA
Tl* the contact owns a 1994 Ford Crown Victoria. The contact stated that while driving approximately 40 MPH, it became difficult to steer the vehicle. The contact stated that the front suspension detached AT the ball joint. The failure caused the brake dust cover to puncture the tire. The vehicle came to an abrupt stop. The vehicle was taken to an independent mechanic to be repaired. The ball joint was replaced along with the brake dust cover. The contact stated that the failure recurred on the passenger's side of the vehicle while driving AT approximately 10 MPH. The vehicle was not taken back to be repaired. A dealer was not contacted.
Owner complaint 11320144 filed with NHTSA
SuspensionFiled Jul 200940,000 milesIL
Tl*the contact owns a 1994 Ford Crown Victoria. The contact stated that the upper and lower ball joints were very noisy while driving 20 MPH. He suggested that they may be rusty due to the high pitch noise he hears throughout the vehicle. The contact inspected the ball joints and stated that they appeared to be damaged. The vehicle has not yet been inspected by a dealer or mechanic. Through online research, he found NHTSA campaign ID number 98v322000 (suspension:front:control arm:lower ball joint). The manufacturer stated that the VIN was excluded from the recall.
Owner complaint 10275484 filed with NHTSA
SuspensionFiled Oct 2007MS
Tl*the contact owns a 1994 Ford Crown Victoria LX. The contact stated that the vehicle squeaked and squealed. The contact refused to provide detailed failure information. She stated that she experienced the same failure listed in the recall. There is a recall for the suspension: front control upper arm upper ball joints and lower ball joints (NHTSA campaign ID #95v194000, 98v322000). The mileage information was unavailable because the odometer failed AT 162,000 miles.
Vehicle description: certain 1996-1999 ford crown victoria police, fleet, natural gas, and 1996-1999 lincoln town car limousine vehicles that were produced with a lower control arm ball joint containing a one piece bearing; and 1990-1996 ford crown victoria police, fleet, and ngv vehicles and 1990-1996 lincoln town car limousine vehicles that have been serviced with either a ball joint containing the one-piece bearing or a front lower control arm containing a ball joint with a one-piece bearing. The one-piece bearing within the lower control arm ball joint CAN weaken slowly during use and eventually crack. This could result in separation of the ball and cap of the joint, allowing the control arm to drop to the ground.
Risk and remedy
Risk
If this occurs while the vehicle is moving, reduced steering control could occur, increasing the risk of a crash.
Remedy
Dealers will replace the lower control arm ball joints (2).
The bolts that attach the front upper control arms to the frame mounting brackets CAN loosen and fracture AT one of the bolt holes causing substantial negative camber and steering pull to the affected side.
Risk and remedy
Risk
If the driver's side bracket fractured AT both bolt holes, the steering control arm CAN contact the steering column shaft and result in a loss of steering control increasing the potential for an accident.
Remedy
Dealers will inspect the torque levels of the four upper control arm mounting bolts, and if any are loose, the brackets will be inspected for damage. If damage is present, it will be repaired.